ARRI WCU-4 User Manual Download Page 15

Page: 15 / 79

Getting started

Calibrating motors

Calibrate the motor(s) by pressing the

CAL

soft button on the

WCU-4

Home

screen or on the motor controller.

NOTICE

Note: Motors must be recalibrated under the following

conditions:

When a motor is detached from the lens
After changing motors
After changing lenses
After a change in a motor position while powered down

NOTICE

Omitting motor calibration might lead to damage of the lens due

to the high level of motor torque!

Using a Pre-Marked Focus Ring

The use of pre-marked focus rings on the WCU-4 hand unit

requires lens data from the motor controller or camera.
Press the WCU-4

MENU

button. Enter the

Pre-Marked Focus

Rings

menu and select a focus ring. Return to

Home

screen by

pressing the

BACK

HOME

button. The selected focus ring will

be indicated next to the numerical focus value in the center of the

screen. The digital focus scale on the display will now align with the

pre-marked focus ring.
You are now ready to shoot.

Summary of Contents for WCU-4
















































































Search results

Summary of Contents for WCU-4

Reviews:

Related manuals for WCU-4

Brands by name

Popular brands

ARRI WCU-4, User Manual

Search results

Summary of Contents for WCU-4

Reviews:

Related manuals for WCU-4

Brands by name

Popular brands