ARRI WCU-4 User Manual Download Page 38

Page: 38 / 79

Menu

11.2 Control Setup

The

Control Setup

screen provides an overview of the current

WCU-4 control configuration.

Control Setup and Knob Setup screens

KNOB
Enter the

Knob Setup

screen by pressing the

KNOB

soft button.

Use the

and

DOWN

soft buttons or the zoom stick to select

Control

and press the

CHANGE

soft button to assign the knob

control to the focus or iris motor or to switch the knob control off.
Use the

and

DOWN

soft buttons or the zoom stick to select

Vibration and press the

CHANGE

soft button to switch vibrations on

digital focus marks on and off.
SLIDER
Enter the

Slider Setup

screen by pressing the

SLIDER

soft button.

Use the

and

DOWN

soft buttons or the zoom stick to select

Control

and press the

CHANGE

soft button to assign the slider

control to the iris or focus motor or to switch the slider control off.

Summary of Contents for WCU-4
















































































Search results

Summary of Contents for WCU-4

Reviews:

Related manuals for WCU-4

Brands by name

Popular brands

ARRI WCU-4, User Manual

Search results

Summary of Contents for WCU-4

Reviews:

Related manuals for WCU-4

Brands by name

Popular brands