ARRI WCU-4 User Manual Download Page 57

Page: 57 / 79

Menu

11.8 User Settings

User Settings

A user setting is a profile of WCU-4 settings. It can be saved to the

SD card and be transferred to a different WCU-4. Up to six user

settings can be stored on or recalled from an SD card.
Load Setting
Select

Load Setting

and use the

and

DOWN

soft buttons or the

zoom stick to select a setting (Setting #1 to #6). Press the

LOAD

soft button or the User button to load the setting.

Save Setting

Select

Save Setting

and use the

and

DOWN

soft buttons or the zoom

stick to select the location you want

to save a new setting to (Setting #1

to #6). Press the

SAVE

soft button or

the User button to save the setting to

the currently selected location. This

will overwrite the previous setting.

User settings menu

screen

Factory Reset
Select

Factory Reset

to reset the WCU-4 to its factory default

settings.

Summary of Contents for WCU-4
















































































Search results

Summary of Contents for WCU-4

Reviews:

Related manuals for WCU-4

Brands by name

Popular brands

ARRI WCU-4, User Manual

Search results

Summary of Contents for WCU-4

Reviews:

Related manuals for WCU-4

Brands by name

Popular brands