ARRI WCU-4 User Manual Download Page 62

Page: 62 / 79

Menu

11.10.1 Region settings

The WCU-4 offers radio settings for different areas (from SUP

02.02.10 and with white-radio module EMIP300). Make sure, that

you select the proper area you are operating the device in. All

available region settings comply with Part 15 of the FCC rules!

1 Go to

MENU > SYSTEM INFO

> RADIO > REGION

2 Use the

and

DOWN

buttons

to select the region you are in.

3 Select

WORLD

if your spe-

cific region is not listed. (The

WORLD

setting provides a ra-

dio output power of 10 dBm

and complies with Part 15 of

the FCC rules. Please make

sure that this complies with the

local radio laws.)

4 Press the

SELECT

soft button

to activate the new region set-

ting.

NOTICE

If the master device (camera or motor controller) is also

equipped with a radio module which is able to set regions, the

master will override the region settings of the WCU-4 with it's

settings.

Summary of Contents for WCU-4
















































































Search results

Summary of Contents for WCU-4

Reviews:

Related manuals for WCU-4

Brands by name

Popular brands

ARRI WCU-4, User Manual

Search results

Summary of Contents for WCU-4

Reviews:

Related manuals for WCU-4

Brands by name

Popular brands