ARRI WCU-4 User Manual Download Page 52

Page: 52 / 79

Menu

Before finally saving the lens file on SD

card, you can edit the lens name that will

be displayed on WCU-4, camera and mo-

tor controller. This name is also used as

the name of the lens file.

Use the

MODE

soft button to select

whether to insert, overwrite or delete a

character.

Press the

SAVE

soft button to finally

save the lens file to SD card folder /AR-

RI/ALEXA/LDA.

You can now upload the lens file from SD

card to the camera or motor controller sup-

porting LDA.

Editing a Lens File

Existing lens files can be edited with the WCU-4 hand unit and then

stored back on the SD card.
Load the lens file to edit onto an SD card in the (folder /ARRI/

ALEXA/LDA) and insert the SD card into the SD card slot of the

WCU-4.
Go to

MENU > LENS DATA > LENS PROGRAMMING > EDIT

LENS FILE

Use the

and

DOWN

soft buttons or the zoom stick to scroll

through the list of lens files on the SD card. Press the

SELECT

soft

button or the User button to select a lens file.

Summary of Contents for WCU-4
















































































Search results

Summary of Contents for WCU-4

Reviews:

Related manuals for WCU-4

Brands by name

Popular brands

ARRI WCU-4, User Manual

Search results

Summary of Contents for WCU-4

Reviews:

Related manuals for WCU-4

Brands by name

Popular brands