Arkon MAGB2 User Manual Download Page 21 | Manualshive

Page: 21 / 54

Arkon MAGB2 User Manual Download Page 21

MAGB2 User Guide

20

V1.7 2021-10-01

9.2. 3G/GPRS/GSM Module

Module Name:

Symbol:

Ordering Code:

MAGB2 3G/GPRS/GSM

Module

******GPRS

APPLICATIONS:

Wireless monitoring of the flowmeter via SMS messages and/or GPRS data transfer

Electrical Specifications
Power Sup. Current

RMS 400mA, MAX 1500mA
External Li-Ion battery 4400mAh 3,6VDC

Operating systems

GSM 850 / GSM 900 DCS 1800 / PCS 1900

SIM Card

3.0 / 1.8 V

Temp. Range

–20 – 70 °C

BASIC CIRCUIT CONNECTIONS:

Using the 3G/GPRS/GSM Module

For more information about installation and specification see document: MAGB2 GPRS-GSM
User Guide.

The meter is sending flow and totalizer information in selected time interval to maximum 3 phone
numbers in form of SMS message and/or GPRS TCP packet to selected IP address and port.

The settings of the SMS and data transfers are done using special GPRS menu in the meter.
The module is capable of sending informations into Arkon.Track.

Warning electrostatic sensitive device.

Any connection or disconnection of any module has to be done with the network power to the
meter switched off.

«
...
19
20
21
22
23
...
»

Summary of Contents for MAGB2























































Reviews:

No comments