background image

Page | 8 

 

Commercial in confidence. Instructions For Use Revision SOR-REV5-090921

 

 

4.  ELECTRONIC FUNCTIONS DESCRIBED 

- Continued

 

 

4.8  Cardiopulmonary Resuscitation (CPR)  

 

NOTE:

 The Cardiopulmonary Resuscitation Function (CPR) is available only on the 

Foot Board Control Panel. 

NOTE: 

Pressing

 

the CPR button will override any locked out functions.

 

 

CAUTION

 

When electronic emergency patient positioning functions are activated, care should 
be taken over the potential of the beds moving parts to either trap or crush the 
patient, caregivers and or other equipment.

 

 
Pressing the SINGLE BUTTON PRESS button, the bed will automatically level all 
positioning functions back to a flat deck position whilst lowering the bed to a safe working 
height. 
 

4.9  Lock Out Function 

 

NOTE:

 The lock out function is only available on the Foot Board Control Panel.

 

 

This facility allows users to selectively disable some of the electrical features of 
the bed. 

In normal operation the key functions of the bed should be in an (unlocked) 

state of use. This is indicated on the control panel by LED lights in between the function 
buttons. 

 

To lock and unlock each function press 

the “lock” button and at the same time press the 

function button that is required to be locked or unlocked. An LED light will illuminate when 
the function is in the locked position. 
 

4.10  Battery Charge Indicator - Battery Backup 

 

 

NOTE:

 The battery charge indicator is only available on Foot Board Control Panel.

 

 

LED

 

light illuminates when the battery is in charge mode. 

 
The battery backup system allows the electrically operated functions to be used for short 
periods when the bed is disconnected from mains power. The bed switches between 
mains and battery power automatically. 
 
The battery is lead-acid and should be charged regularly and not be allowed to discharge 
fully. Fully discharging the battery will cause a reduction in battery life. 
 
To charge the battery, connect the power cord to the mains supply. This should be done 
as often as possible to maximise battery life. If the bed is not used for a long period of 
time, it is recommended that the batteries are charged in accordance with the section on 
Transportation and Storage within this manual. 

 

WARNING

 

Do not expose the battery to open flame or immerse in liquid.

 

 

Summary of Contents for Sorrento Floor Bed

























Reviews: