background image

21

Preventive Maintenance Schedule

The Semi-Permanent Rack is subject to wear and the following actions must be performed

when  specified  to  ensure  that  the  product  remains  within  its  original  manufacturing

specifications.

The  Semi-Permanent  Rack  must  be  inspected  by  a  qualified Arjo  technician  on  an  annual

basis to ensure the proper functioning of its components, as well as the safety of the patients

and care givers that use the Semi-Permanent Rack. Please contact your local representative

to make arrangements.

Cleaning

To clean the 

Semi-Permanent Rack

, wipe it down with a damp cloth using warm water and

mild detergent. 

To ensure a smooth rolling surface for the trolley wheels, clean the inside of the track every

four months. To do so, insert a damp cloth in the opening and slide it from one end of the track

to the other.

POINTS TO BE INSPECTED BY

USER/SERVICE TECHNICIAN

FREQUENCY

Annually or 1400 cycles

Monthly

Before every use

  

Inspect for evidence of external damage or missing parts.

Make sure that all bolts and nuts are properly tightened.

Make sure that the levelling feet are properly adjusted.

Make sure that the track is properly assembled to the posts.

Make sure that all posts are straight.

Clean the inside of the tracks to make sure that there is no dust or grease build-

up inside the tracks.

Make sure that the trolleys move freely along the tracks.

WARNING: Safety related maintenance and authorized service must be carried out by

qualified personnel, fully trained in servicing procedures by Arjo and equipped with

the  correct  tools  and  proper  documentation,  including  the  parts  list  and  service

manual. Failure to meet these requirements could result in personal injuries and/or

unsafe equipment.

WARNING:  The  points  on  this  checklist  are  the  minimum  the  manufacturer

recommends.  In  some  cases  more  frequent  inspections  should  be  carried  out.

Continuing to use the Semi-Permanent Rack without conducting regular inspections

will seriously compromise the user's and patient’s safety. Preventive maintenance

specified in this manual can prevent accidents.

WARNING:  If  any  of  the  above  inspection  points  fails,  DO  NOT  USE  the  Semi-

Permanent Rack until appropriate corrective action is taken.

NOTE: If the product does not work as intended, immediately contact your local Arjo

agent for support.

CAUTION: Do not use phenol, chlorine or other types of solvent that may damage the

finish.

Care and Maintenance

Summary of Contents for KWIKtrak 4-Post





























Reviews: