Arjo Huntleigh Sonicaid Team3 USA Instructions For Use Manual Download Page 23

Page: 23 / 84

Instructions For Use

Unlock Code

Service Code

Patient Data Code

Settings Management

NIBP Protocol

Touch

to return to previous page.

accepts data and

does not.

returns to Main

Application screen.

For all Menu and sub menu screens the options are selected/deselected by touching on the icons as

follows:

Option disabled

Option enabled

Option not selected

Option selected

Increases selection

Decreases selection

Settings Main Menu

Touch each category to access the sub menu options available.

Note: The Trace Offsets sub menu is only available if not printing or recording.

Note: The Trace Offsets sub menu is only visible when ultrasound transducers are plugged into the

FHR1 and FHR2 sockets on the frontof the unit.

Note: Team3 will return all settings to Default levels when switched off. Default settings can be

customised - refer to Section 13.5.
Note: If the mains supply is interrupted for more than 30 seconds when no backup battery is

provided, the Team3 shall revert to Default settings.

Summary of Contents for Huntleigh Sonicaid Team3 USA





















































































Search results

Summary of Contents for Huntleigh Sonicaid Team3 USA

Reviews:

Related manuals for Huntleigh Sonicaid Team3 USA

Brands by name

Popular brands

Arjo Huntleigh Sonicaid Team3 USA, Instructions For Use Manual

Search results

Summary of Contents for Huntleigh Sonicaid Team3 USA

Reviews:

Related manuals for Huntleigh Sonicaid Team3 USA

Brands by name

Popular brands