Aritech 1X-E4 Series Operation Manual Download Page 14 | Manualshive

Page: 14 / 29

background image

8

1X-E4 Series Operation Manual

Battery power and battery fuse fault indication:
•  General Fault LED: Flashing.
•  Supply Fault LED: Flashing.
•  Control panel buzzer: Sounding intermittent.
Earth fault indication:
•  General Fault LED: Flashing.
•  Earth Fault LED: On steady.
•  Control panel buzzer: Sounding intermittent.

Note:

Contact your installation or maintenance contractor to investigate the

cause of all reported faults.

Disablements

Disabled zones are indicated as follows:
•  General Disable LED: On steady.
•  Corresponding Zone LED: On steady yellow.
•  Control panel buzzer: Off.
Disabled evacuation areas are indicated as follows:
•  General Disable LED: On steady.
•  Evacuation Area LED: On steady yellow.
•  Control panel buzzer: Off.
Disabled fire routing is indicated as follows:
•  General Disable LED: On steady.
•  Fire Routing LED: On steady yellow.
•  Control panel buzzer: Off.
Disabled expansion boards are indicated as follows:
•  General Disable LED: On steady.
•  I/O LED: On steady yellow.
•  Control panel buzzer: Off.
Disabled fault warning (if configured) is indicated as follows:
•  General Disable LED: On steady.
•  Fault Warning LED: On steady yellow.
•  Control panel buzzer: Off.

«
...
12
13
14
15
16
...
»

Summary of Contents for 1X-E4 Series






























Reviews:

No comments

Related manuals for 1X-E4 Series

Brand: Febco Pages: 4

Brand: Cisco Pages: 48

Brand: Samsung Pages: 32

Brand: Eaton Pages: 100

Brand: Gardena Pages: 14

Brand: Gardena Pages: 8

Brand: Nedap Pages: 20

1E0671-1 MCR2.9

Brand: Haberl Electronic Pages: 9

Brand: J+J Pages: 2

Brand: National Instruments Pages: 72

Brand: National Instruments Pages: 41

MAGNUM ALERT 3000 FIRE ALARM

Brand: NAPCO Pages: 2

Brand: Dantel Pages: 6

GAMMA VERSUS Series

Brand: JCM Pages: 111

767-4804/000-800

Brand: WAGO Pages: 80

Brand: micro-trak Pages: 44

Brand: Joy-it Pages: 7

Brand: Woodward Pages: 112

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands