Aritech 1X-E4 Series Operation Manual Download Page 27

Page: 27 / 29

1X-E4 Series Operation Manual

Maintenance

Perform the following maintenance tasks to ensure that your fire alarm system

works correctly and complies with all required European regulations.

Note:

Before performing any tests, ensure that fire routing is disabled or that the

fire brigade has been notified.

Quarterly maintenance

Contact your installation or maintenance contractor to perform a quarterly

inspection of the fire alarm system.
This inspection must test at least one device per zone and verify that the control

panel responds to all fault and alarm events. The control panel power supply and

battery voltage should be checked.

Annual maintenance

Contact your installation or maintenance contractor to carry out an annual

inspection of the fire alarm system.
This inspection must test all system devices and verify that the control panel

responds to all fault and alarm events. All electrical connections must be visually

inspected to make sure that they are securely fastened, that they have not been

damaged, and that they are appropriately protected.

Cleaning

Keep the outside and inside of the control panel clean. Carry out periodic

cleaning using a damp cloth for the outside. Do not use products containing

solvents to clean the unit. Do not clean the inside of the cabinet with liquid

products.

Summary of Contents for 1X-E4 Series






























Search results

Summary of Contents for 1X-E4 Series

Reviews:

Related manuals for 1X-E4 Series

Brands by name

Popular brands

Aritech 1X-E4 Series, Operation Manual

Search results

Summary of Contents for 1X-E4 Series

Reviews:

Related manuals for 1X-E4 Series

Brands by name

Popular brands