Argox Xellent X-1000VL User Manual Download Page 43

Page: 43 / 124

enters BACK
DISTANCE setting.

BACK
DISTANCE

10~40 mm

21 mm

Available only when
BACK FEED is
enabled.

BASE
DARKNESS

0~99 (PPLA)

-28~28 (PPLB)

Available only in
PPLA and PPLB
printer languages.

ABS.
DARKNESS

0~30

To select darkness.
Available only in
PPLZ printer
language.

TRIM.

DARKNESS

-30~30

To fine-tune
darkness. Available
only in PPLZ printer
language.

BAUD RATE
(RS232)

600 / 1200 / 2400/
4800 / 9600 /

19200 / 38400 /
57600 / 115200

9600

Should be as same as
setting of host.

PARITY
(RS232)

NONE

EVEN

ODD

NONE

Should be as same as
setting of host.

LENGTH
(RS232)

8 DATA BITS

7 DATA BITS

8 DATA BITS Should be as same as

setting of host.

CLEAR FLASH NO

YES

When “YES” is
selected, all the label
forms, soft fonts, and
graphics stored will be
deleted.

Summary of Contents for Xellent X-1000VL





























































































































Search results

Summary of Contents for Xellent X-1000VL

Reviews:

Related manuals for Xellent X-1000VL

Brands by name

Popular brands

Argox Xellent X-1000VL, User Manual

Search results

Summary of Contents for Xellent X-1000VL

Reviews:

Related manuals for Xellent X-1000VL

Brands by name

Popular brands