Arctic Cat DVX 90/90 UTILITY Service Manual Download

Page: 62 / 86

CLEANING AND INSPECTING

1. Clean all gas tank components with parts-cleaning

solvent.

2. Inspect all hoses for cracks or leaks.

3. Inspect gas tank cap and tank for leaks, holes, and

damaged threads.

INSTALLING

1. Place the gas tank into position on the frame; then

install the gas hoses to the gas tank valve on the

frame according to the tags made during removing.

MD2394

2. Install and tighten the gas tank cap screws securely.



NOTE: Do not over-tighten the cap screws securing

the gas tank.

MD2393

3. Install the front fender panel with the eight washers,

four Phillips-head cap screws, and six nuts and

tighten securely.



NOTE: Do not over-tighten the cap screws and nuts

securing the front fender panel.

4. Install the gas tank cap.

5. Install the handlebar aligning the pins in the lower

clamps with the locating holes in the bottom of the

handlebar. Place the top caps into position; then

tighten the cap screws to 10 ft-lb.

MD2138

Gas Tank Valve

This ATV has a valve mounted on the side of the frame

separate from the gas tank. There are three positions: ON,

RES, and OFF.

KM043A

In the OFF position, the valve will not allow gasoline to

flow to the carburetor. In the ON position (the normal

operating position), gasoline will flow from the tank to

the carburetor. In this position, 1.3 L (0.34 U.S. gal.) of

gasoline will remain in the tank as a reserve quantity.

Moving the valve to the RES position will allow the

operator to use the remaining gasoline in the tank. When

turning the valve to any of the three positions, be sure the

indicator is pointed directly at the position desired.

REMOVING/INSPECTING

1. Remove the cap screw securing the valve to the

frame; then pull the valve out far enough to gain

access to the three gas hoses (two to the gas tank, one

to the carburetor).

2. Remove the gas hoses from the valve by releasing

the spring clamps.

3. Inspect for and remove any obstructions in the valve.

INSTALLING

1. Install the gas hoses onto the valve with the spring

clamps.

! WARNING

Drain the gas tank prior to this procedure.

Summary of Contents for DVX 90/90 UTILITY























































































Search results

Summary of Contents for DVX 90/90 UTILITY

Reviews:

Related manuals for DVX 90/90 UTILITY

Brands by name

Popular brands

Arctic Cat DVX 90/90 UTILITY, Service Manual

Search results

Summary of Contents for DVX 90/90 UTILITY

Reviews:

Related manuals for DVX 90/90 UTILITY

Brands by name

Popular brands