Arctic Cat DVX 90/90 UTILITY Service Manual Download

Page: 38 / 86

YT169A

7. Make sure the crankshaft is positioned at TDC; then

install the camshaft with the single large reference

hole (A) directed up and the two small timing holes

(B) parallel to the top of the cylinder head.

YT095A

YT173A

8. Place the camshaft holder into position on the cylin-

der head making sure the camshaft bearings are

seated correctly; then install four flat washers (A)

and four nuts (B). Tighten in a crisscross pattern to

15 ft-lb.

YT172A

9. Install the two cap screws securing the left side of the

cylinder head and cylinder to the crankcase and

tighten to 7 ft-lb.

YT098B

10. Install the cam chain tensioner assembly into the cyl-

inder using a new gasket; then secure with two cap

screws and tighten to 7 ft-lb.

YT098C

11. Using a small flat screwdriver, release the cam chain

tension spring by rotating clockwise; then install the

plug bolt and tighten securely.

12. Adjust the valve/tappet clearance (see the Periodic

Maintenance/Tune-Up section); then install the valve

cover with new gasket. Tighten the cap screws to 7

ft-lb.

Summary of Contents for DVX 90/90 UTILITY























































































Search results

Summary of Contents for DVX 90/90 UTILITY

Reviews:

Related manuals for DVX 90/90 UTILITY

Brands by name

Popular brands

Arctic Cat DVX 90/90 UTILITY, Service Manual

Search results

Summary of Contents for DVX 90/90 UTILITY

Reviews:

Related manuals for DVX 90/90 UTILITY

Brands by name

Popular brands