Arctic Cat DVX 90/90 UTILITY Service Manual Download

Page: 27 / 86

Engine/Transmission

This section has been organized into sub-sections which

show a progression for the complete servicing of the Arc-

tic Cat Y-12+ engine/transmission.



NOTE: Arctic Cat recommends the use of new gas-

kets, lock nuts, and seals and lubricating all internal
components when servicing the engine/transmission.

Removing Engine/

Transmission

1. Turn the gas tank valve to the OFF position; then

remove the seat and disconnect the negative battery

cable securing it away from the battery.

CD643

KM853A

2. Drain the transmission lubricant.



NOTE: The drain plug is located on the bottom of

the transmission.

KM038A

3. Drain the engine oil.



NOTE: The drain plug is located at the left-rear of

the engine.

KM041A

4. Remove the left and right footwells and the left-side

footwell mounting plate; then remove the drive

sprocket and chain from the transmission output shaft.

YT002A

YT009

! WARNING

Battery acid is harmful if it contacts eyes, skin, or cloth-
ing. Care must be taken whenever handling a battery.

Summary of Contents for DVX 90/90 UTILITY























































































Search results

Summary of Contents for DVX 90/90 UTILITY

Reviews:

Related manuals for DVX 90/90 UTILITY

Brands by name

Popular brands

Arctic Cat DVX 90/90 UTILITY, Service Manual

Search results

Summary of Contents for DVX 90/90 UTILITY

Reviews:

Related manuals for DVX 90/90 UTILITY

Brands by name

Popular brands