Arctic Cat DVX 90/90 UTILITY Service Manual Download

Page: 53 / 86

YT012

3. Install the rear engine mounting through-bolt and

nut; then tighten the front and rear nuts to 32.5 ft-lb.

4. Install the drive sprocket and chain and secure with

the spline-lock; then install the cap screws and

tighten to 8 ft-lb.

YT009A

5. Install the V-belt housing cooling duct and secure

with the clamp; then install the exhaust pipe/muffler

assembly using a new grafoil seal in the cylinder

head. Tighten the exhaust pipe to cylinder head nuts

to 7 ft-lb and the muffler mounting cap screws to 32

ft-lb.

YT008A

YT005A

6. Connect the shift linkage; then install the air filter

housing and air filter. Tighten all hardware securely.

YT007A

YT003A

7. Connect the starter harness connector (A), stator coil

connector (B), and electric choke connector (C); then

install the spark plug cap.

YT010A

Summary of Contents for DVX 90/90 UTILITY























































































Search results

Summary of Contents for DVX 90/90 UTILITY

Reviews:

Related manuals for DVX 90/90 UTILITY

Brands by name

Popular brands

Arctic Cat DVX 90/90 UTILITY, Service Manual

Search results

Summary of Contents for DVX 90/90 UTILITY

Reviews:

Related manuals for DVX 90/90 UTILITY

Brands by name

Popular brands