En
gl
is
h
mo
vie
5.1
so
l
o
technical
specification
Pre-amplifier
Inputs
Maximum input level
2.5Vrms
Input impedance
47k
Ω
Signal/noise ratio
105dB
Line level outputs
Maximum output level
2.5Vrms
Output impedance
120
Ω
Optical output (TOSLINK)
Sample rate
Up to 96kHz, depending on
source
Amplifier
Continuous power output, per channel, 80kHz measurement
bandwidth
Five channels, 8
Ω
, 1kHz
50Wrms, 0.02% THD+n
Five channels, 4
Ω
, 1kHz
75Wrms, 0.05% THD+n
Distortion, five channels, 4
Ω
, 80%
power, 1kHz
0.011% THD+n
Video outputs
Composite video
1 x gold plated phono. 1V pk-pk in 75
Ω
Component video
Interlaced or Progressive
3 gold plated phono sockets.
Y 1V pk-pk in 75
Ω
, Pb 0.7V pk-pk in 75
Ω
, Pr
0.7V pk-pk in 75
Ω
SCART socket with
RGB video (where
fitted)
All 0.7V in 75
Ω
, composite video 1V in 75
Ω
, and
stereo audio
Auto switching of TV with aspect ratio control
HDMI
19-pin HDMI connector
Supported video formats are:
720 x 576p, 720 x 480p, 1280 x 720p,
1920 x 1080i
audio to 2-channel/96kHz (24-bit).
CD/DVD-A/SACD playback
Digital-Analogue Conversion
CS42528 24-bit/192kHz DAC
differential output
Frequency response (±0.5dB)
20Hz–20kHz
DAB receiver (where fitted)
DAC
AKM 96kHz 24-bit Delta-Sigma
DAC
RF tuning range
174–240MHz (Band III)
1452–1490MHz (L-band)
Sensitivity (typical)
–98dBm (VHF measurement to
EN50248)
Input impedance
50
Ω
Audio data rate (maximum)
256kbits/s MPEG layer II,
protection level 3
Number stored services
(maximum)
128
FM receiver
RF tuning range
87.5–108MHz
Sensitivity (typical)
2µV
Signal/noise ratio (at 200mV)
58dB
Distortion (THD at 200mV)
0.5%
AM receiver (where fitted)
RF tuning range
522–1611kHz
Signal/noise ratio (at 200mV)
40dB
Distortion (THD at 30%
modulation)
1.5%
General
Supply voltage*
115V or 230V AC,
depending on shipping region
Power consumption
Operational 50W (typical), 400W
(maximum);
Stand-by <5W;
Hard stand-by <1W
Size (W x D x H)
W430mm x D350mm x H79mm
Weight (net)
7.75kg
Weight (packed)
10.5kg
Supplied accessories
Mains lead
CR100 remote control and four
AAA batteries
Wire dipole aerial (Band III)
Handbook and registration card
*
Solo Movie 5.1 is fitted with a transformer designed to accept the
mains voltage in the region that the product was shipped to. If your
mains supply voltage does not match this specification (as shown
on the rear panel), or you wish to take the unit to a region with a
different main voltage, or the mains plug is incorrect, please consult
your Arcam dealer.
This product is a Class II or double insulated electrical appliance. It
has been designed in such a way that it does not require a safety
connection to electrical earth (U.S. = ground).
E&EO
Note that all specification values are typical unless otherwise stated.
Continual improvement policy
Arcam has a policy of continual improvement for its products. This means
that designs and specifications are subject to change without notice.
