manualshive.com logo in svg

Aprilaire 8800, Programmer'S Manual

Share
Download
Aprilaire 8800 Programmer'S Manual Download Page 44

HUMIDITy CONTROl COMMANDS

SHUM

Controlling humidification setpoint

COS: C5

Permissions: Read/Write

Query 
Command

Syntax: 

SN[#] SHUM?<CR>

Description:  Requests the controlling humidification setpoint .

Assignment 
Command

Syntax: 

SN[#] SHUM=[value]%<CR>

Description:  Sets the controlling humidification setpoint to 

[value]

 .

Example: 

SN1 SHUM=45%<CR>

Response or 
COS Message

Syntax: 

SN[#] SHUM=[value]%<CR>

Example: 

SN1 SHUM=45%<CR>

 

   

Node address 1 responds with a controlling humidification setpoint of 45% .

Parameters 

Range

value:

 humidistat setpoint in %RH 

[10 – 90]

The controlling humidification setpoint corresponds to the active setpoint to which the humidistat is controlling the humidification equipment . 
Assignment commands are ignored if the controller type is set to thermostat .
When the humidistat system mode is set to AUTO, the controlling mode is determined by the humidistat . In addition, when the humidistat 
system mode is set to AUTO, the Humidification and Dehumidification setpoints are interdependent and must abide by the fixed deadband . If 
an assignment command is received with a setpoint value that causes a deadband violation, the opposite setpoint is automatically increased 
or decreased to fulfill the deadband requirement . If the deadband requirement cannot be fulfilled by increasing or decreasing the opposite 
setpoint, the command is ignored and no response sent .
Integer values must be within the range specified . The humidification setpoint can be changed through the Home Screens for humidistat 
control . If the humidification setpoint is changed at the thermostat, a C5 COS unsolicited message is issued (if C5 is ON) .

 

SHUM++, SHUM--

Increment or decrement the controlling humidistat humidification setpoint

COS: N/A

Permissions: Write only

Assignment 
Command

Syntax: 

SN[#] SHUM++=[value]%<CR>

Syntax: 

SN[#] SHUM--=[value]%<CR>

Description:  Increments or decrements the controlling humidification setpoint to 

[value]

 based on the ++/-- .

Examples: 

SN1 SHUM++=3%<CR>

 

  

SN1 SHUM--=5%<CR>

Response

Syntax: 

SN[#] SHUM++=[value]%<CR>

Syntax: 

SN[#] SHUM--=[value]%<CR>

Example: 

SN1 SHUM++=5%<CR>

 

   

Node address 1 responds with incrementing the humidification setpoint by 5% RH .

Parameters 

Range

value:

 controlling humidification setpoint increment or decrement value

The controlling humidification setpoint corresponds to the active setpoint to which the humidistat is controlling the humidification equipment . 
This command is ignored if the controller type is set to thermostat .
If the resultant setpoint is outside the allowable range for the humidification setpoint, the command is ignored .

44

Summary of Contents for 8800

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands