manualshive.com logo in svg

Aprilaire 8800, Programmer'S Manual

Share
Download
Aprilaire 8800 Programmer'S Manual Download Page 22

EVTCfg

Thermostat program event configuration

COS: N/A

Permissions: Read/Write

Query 
Command

Syntax: 

SN[#] EVTCFG?<CR>

Description:  Requests the program event configuration setting .

Assignment 
Command

Syntax: 

SN[#] EVTCFG=[value]<CR>

Description:  Sets the program event configuration setting to 

[value]

 .

Example: 

SN1 EVTCFG=RES<CR>

Response

Syntax: 

SN[#] EVTCFG=[value]<CR>

Example: 

SN1 EVTCFG=RES<CR>

 

   

Node address 1 responds with an event configuration setting of residential .

Parameters 

Range

value:

 program format code 

[RES, COM]

 

RES:

 residential event labels

 

COM:

 commercial event labels

If the program event configuration is set to commercial, the events per day setting is automatically set to 2 events per day . 
This command is ignored if the controller type is set to humidistat . 

 

EVTSDAy

Thermostat program events per day

COS: C13

Permissions: Read/Write

Query 
Command

Syntax: 

SN[#] EVTSDAY?<CR>

Description:  Requests the program events per day setting .

Assignment 
Command

Syntax: 

SN[#] EVTSDAY=[value]<CR>

Description:  Sets the program events per day setting to 

[value]

 events per day .

Example: 

SN1 EVTSDAY=4<CR>

Response or 
COS Message

Syntax: 

SN[#] EVTSDAY=[value]<CR>

Example: 

SN1 EVTSDAY=4<CR>

 

   

Node address 1 responds with an events per day setting of 4 .

Parameters 

Range

value:

 program events per day 

[2, 4] 

 

4:

 four events per day 

 

2:

 two events per day

If the EVTCFG setting is set to commercial, the EVTSDAY setting is fixed at 2 .
This command is ignored if the controller type is set to humidistat . If the program events per day setting is changed at the thermostat, a C13 
COS unsolicited message is issued (if C13 is ON) .

22

Summary of Contents for 8800

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands