manualshive.com logo in svg

Aprilaire 8800, Programmer'S Manual

Share
Download
Aprilaire 8800 Programmer'S Manual Download Page 40

SC

Controlling thermostat cool setpoint

COS: C5

Permissions: Read/Write

Query 
Command

Syntax: 

SN[#] SC?<CR>

Description:  Requests the controlling thermostat cool setpoint .

Assignment 
Command

Syntax: 

SN[#] SC=[value]<CR>

Description:  Sets the controlling thermostat cool setpoint to 

[value]

 .

Example: 

SN1 SC=78<CR>

Response or 
COS Message

Syntax: 

SN[#] SC=[value][scale]<CR>

Example: 

SN1 SC=78F<CR> 

   

Node address 1 responds with a controlling cool setpoint of 78°F .

Parameters 

Range

value:

 cool setpoint 

  Fahrenheit 

[42 – 99] 

  Celsius 

[6 – 37]

scale:

 temperature scale 

[F, C] 

 

F:

 Fahrenheit 

 

C:

 Celsius

The thermostat controlling cool setpoint corresponds to the active cool setpoint to which the thermostat is controlling the cooling equipment . 
Assignment commands are ignored if the controller type is set to humidistat .
When the thermostat system mode is set to AUTO, the heat and cool setpoints are interdependent and must abide by the deadband . If an 
assignment command is received with a cool setpoint value that causes a deadband violation, the heat setpoint is automatically decreased 
to fulfill the deadband requirement . If the deadband requirement cannot be fulfilled by decreasing the heat setpoint, the command is ignored 
and no response sent .
If an assignment command is received while the thermostat is running the program schedule, the thermostat automatically initiates a 
temporary hold with an end time of the start time of the next scheduled event . If a hold is active at the time of the assignment command, 
the hold setpoint is modified . In addition, if a hold is initiated as a result of the receipt of this command, a C17 COS unsolicited message is 
issued (if C17 is ON) .
If a query or an assignment command is received and the thermostat program format is programmable (i .e . not non-programmable), and the 
system mode is set to Heat, Emergency Heat or OFF, this command is ignored .
Integer values must be within the range specified for the current temperature scale . The cool setpoint can be changed through the Home 
Screens for thermostat control or due to a schedule or hold change . If the cool setpoint is changed at the thermostat, a C5 COS unsolicited 
message is issued (if C5 is ON) .

40

Summary of Contents for 8800

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands