APQS Lucey Deluxe Table Manual Download Page 51

Page: 51 / 81

9-1-2022

APQS.com

Lucey Operation

With each pressing of the toggle switch (toward the white dot on your handle), the machine will make a

“half stitch.” You may continue pressing the button to place precise stitches where you want them.

You can also keep the toggle switch pressed toward the white dot rather than pressing it

repeatedly. This will make the machine cycle through a complete “UP-DOWN” sequence so that

you can make full stitches. Place these stitches close together to secure your stitches. Place at

least 8

–

10 stitches right next to each other for a firm, secure start.

When you release the toggle switch, the machine will cycle the needle into the up or down

position.

If you wish to change the needle position from where it stopped, press the toggle switch toward

the white dot once more.

To end your stitches and secure your top and bobbin thread, stop sewing about ¼-inch away from your

actual intended stopping point. Use the “Needle Up/Down” toggle switch again (press the toggle switch

on any handle toward the white dot) to place very close stitches for securing the thread.

Stitch Regulated & Manual Stitching Modes

Stitch Regulated

The Stitch

Regulator is active

when the blue LED

light next to the

Stitch Regulator

On/Off switch IS

illuminated.

The numbers around the dial correspond to “stitches per inch” when using the

Stitch Regulated sewing mode. For example, in the photo above the dial is

pointing near the number 10, indicating the machine will sew approximately 10

stitches every inch.

When the Stitch Regulator is active, you may select a stitch length from 7

–

stitches per inch by turning the dial to the desired length. Most quilters find

stitches between 10

–

11 stitches per inch to be the most pleasing, but you can

select a length that suits you.

If you stop moving the machine in Stitch Regulated Mode, but do not tap the

sewing motor toggle switch, the machine is still active but will not stitch until

you move it again. Your machine head will BEEP every few seconds to remind

you that your machine motor is still ON. Tap the toggle switch on any handle

away from the white dot to stop the sewing motor completely.

NOTE:

You can change this setting as you sew; you will not have to

stop the sewing motor to adjust your stitch length.

Summary of Contents for Lucey Deluxe Table


















































































Search results

Summary of Contents for Lucey Deluxe Table

Reviews:

Related manuals for Lucey Deluxe Table

Brands by name

Popular brands

APQS Lucey Deluxe Table, Manual

Search results

Summary of Contents for Lucey Deluxe Table

Reviews:

Related manuals for Lucey Deluxe Table

Brands by name

Popular brands