manualshive.com logo in svg

Approach Engineering AH-64A Apache-50, Instruction Manual, Page: 35 / 46

Share
Download
Approach Engineering AH-64A Apache-50 Instruction Manual Download Page 35

APACHE 50                      PAGE #  35 

                                                                                         Dawson’s 

APPROACH E GI EERI G  

                                                                                                                         AH-64A  50  MECHA ICS 

22.7  

Punch out the TADS night side end piece, TADS-4.  For 

ease of finishing sand a rounded edge on the end piece.  Glue it 
on the end of the night assembly.   

22.8  

Punch out the TADS day side end piece, TADS-5, and 

glue it on the end of the day side assembly.  

22.9  

Sand the TADS optical faces to the desired shape.  For 

ease of finishing you may want to finish the two sides before the 
next step.  

22.10  

Punch out the TADS center mount, TADS-3, from the 

¼” balsa sheet.  Glue the completed TADS night and day side 
assemblies one on each side. 

 

22.11  

Glue the completed assembly on the bottom side of the 

TADS/PNVS support plate.  Punch out the ¼” balsa TADS 
lower support mount, TADS-6, and glue in the notch provided 
by the nose support plate and under the TADS bucket assembly. 

 

 otes: 

22.0  TADS A D P VS 
         ASSEMBLY 

Summary of Contents for AH-64A Apache-50















































Reviews:

No comments