manualshive.com logo in svg

Approach Engineering AH-64A Apache-50, Instruction Manual, Page: 32 / 46

Share
Download
Approach Engineering AH-64A Apache-50 Instruction Manual Download Page 32

APACHE 50                      PAGE #  32 

                                                                                         Dawson’s 

APPROACH E GI EERI G  

                                                                                                                         AH-64A  50  MECHA ICS 

20.7  

Slide on the ¼” balsa gun front, GNF, over the brass tube 

so that the cylindrical cut is facing toward the gearbox formers.  
When satisfied with the fit glue in place. 

20.8  

Punch out the gun frame back, GFB, two gun frame 

sides, GFS, and one gun frame front, GFF, from the ¼” balsa 
sheet.  Glue the gun frame sides on the INSIDE of the gun 
frame front and back.  This makes the cradle for the gun assem-
bly.  Set aside until further assembly. 
.  

20.9  

Slide the gun assembly into the frame assembly created 

earlier.  The gun barrel should be concentric with the frame and 
the gun body should fit in the notch on the back of the frame.  
When satisfied glue in place. 

20.10  

Punch out the 1/4” balsa gun mount back GMB.  Posi-

tion over the gun body to align the lower edge to the lower sur-
face of the body and centered horizontally.  When satisfied glue 
in place. 

20.11  

Punch out the 1/8” ply gun recoil adapter, GRA, and 

slide it over the brass barrel tube.  Using the two lengths of 1/8” 
wood dowels glue the assembly together so that the dowels are 
between the recoil adapter and the gun front. For ease of finish-
ing you may want to paint and detail the gun and gun frame at 
this time before final assembly.  

 

20.12  

Note: the gun is stowed in a nose up position when not 

in use.  For ease of finishing you may want to paint and detail 
the gun at this time before final assembly.  Slide the gun assem-
bly into the frame and glue in place.  Slide the frame up into the 
mount and glue at the desired angle.

 

20.0  30mm CA  O  ASSEMBLY 
         ASSEMBLY 

Summary of Contents for AH-64A Apache-50















































Reviews:

No comments