manualshive.com logo in svg

Approach Engineering AH-64A Apache-50, Instruction Manual, Page: 25 / 46

Share
Download
Approach Engineering AH-64A Apache-50 Instruction Manual Download Page 25

APACHE 50                      PAGE #  25 

                                                                                         Dawson’s 

APPROACH E GI EERI G  

                                                                                                                         AH-64A  50  MECHA ICS 

17.1  

Temporarily install the transmission cover on the fuse-

lage.  Using 3/32” balsa cross sheet the fuselage starting just 
behind the transmission.   Check to make sure that the sides are 
properly matched.  When satisfied continue to the next step. 

17.2  

Continue cross sheeting the top of the tail boom to the 

end of the tail boom.  Cut away any sheeting by the tail rotor 
control pushrod for free movement. 

17.3  

Cut out the ¾” x 4.6” triangle stock to match the cross 

sheeting and flush with the top of the leading edge former.  Glue 
the triangle stock centered on the leading edge supports.  

17.4  

 Punch out the 1/16” balsa trailing edge former, VF-5, 

and glue it into the lower trailing edge slot of the vertical fin 
assembly.  Center and glue the ¼” brass horizontal fin tube into 
the holes of the vertical fin assembly. 

 

17.5  

Punch out the two 1/16” balsa vertical fin side sheeting 

VFS.  Sand the leading edge at an angle so that when it is mated 
with the tri-stock leading edge it will be a flush fit.  When satis-
fied with the fit apply CA+ to the leading edge and glue in 
place. 

 

17.6  

For ease of bending slightly wet the side sheeting.  Apply 

CA+ to the vertical frame and sides and bend into place.  Sand 
the leading edge to match the contour and to a rounded profile. 

 

17.0  VERTICAL FI  ASSEMBLY 
       PROCEDURE 

Sand Flush 

Sand to Match 
Sheeting 

VF

-5 

Summary of Contents for AH-64A Apache-50















































Reviews:

No comments