manualshive.com logo in svg

API A790, Operation Manual

Share
Download
API A790 Operation Manual Download Page 119

 

Troubleshooting 8-11 

Power Management Problems 

The computer does not enter Standby or Hibernation mode 
automatically. 

z

 

If you have a connection to another computer, the computer does not 
enter Standby or Hibernation mode if the connection is actively in 
use. 

z

 

Make sure that the Standby or Hibernation time-out is enabled. 

The computer does not enter Standby or Hibernation mode 
immediately. 

z

 

If the computer is performing an operation, it normally waits for the 
operation to finish. 

The computer does not resume from Standby or Hibernation mode. 

z

 

The computer automatically enters Standby or Hibernation mode 
when the battery pack is empty. Do any one of the following: 

−

  Connect the AC adapter to the computer. 

−

  Replace the empty battery pack with a fully charged one. 

The computer does not enter Hibernation mode with the 

Fn

+

F10

 hot 

keys. 

z

 

Make sure that the Hibernation function is specified for the sleep 
button. 

z

 

You might be using a PC card that prevents the computer from 
entering Hibernation mode. To enter the mode, stop the 
communication program and then remove the card or stop the card. 

Printer Problems 

The printer does not work. 

z

 

Make sure that the printer is turned on (if it comes with an 
independent power source) and is online (ready to use). 

z

 

Make sure that the printer’s signal cable is properly connected. 

Summary of Contents for A790











































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands