manualshive.com logo in svg

API A790, Operation Manual

Share
Download
API A790 Operation Manual Download Page 100

 

Installing Software Drivers 

6-12 

GPS Driver 

To install the GPS driver, perform the following: 

1.

 

Insert the driver disc into the optical drive. 

2.

 

Click 

Start

 

Æ

 

Run

. 

3.

 

Enter the driver path and file name (e.g., 

g:\GPS\PL-2303 

Driver Installer_GPS.exe

), then click 

OK

. 

 

4.

 

When the 

InstallShield Wizard

 screen appears, click 

Next

 to continue. 

5.

 

When the 

Windows Logo Compatibility Test

 screen appears, click 

Continue Anyway

. 

6.

 

When the next screen appears, click 

Finish

 to exit the first part of the 

driver installation. 

7.

 

Re-boot your system for the changes to take effect. 

8.

 

After the system has finished rebooting, the 

Found New Hardware 

Wizard

 screen would appear. Select 

Install the software automatically

 

(Recommended)

, then click 

Next

. 

9.

 

When the 

Windows Logo Compatibility Test

 screen appears, click 

Continue Anyway

. 

10.

 

When the next screen appears, click 

Finish

 to complete driver 

installation. 

Summary of Contents for A790











































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands