background image

 
MND 

Rev. A, 6/15

30

MPX Series Magnetostrictive

Input Registers (0x04):

Register 

Type  

Returned Data

30300   

U16 

Raw Top Float Reading (in mm, unsigned)

30301   

U16 

Raw Bottom Float Reading (in mm, unsigned)

30302   

S16 

Temperature Reading (in 

0

C, signed)

30303-30304 

U32 

Calculated Top Float Reading (in selected Units) 

30305-30306 

U32 

Calculated Bottom Float Reading (in selected Units) 

Holding Registers (0x03):

Register  

Type 

Description

     Value Range

40400   

U16 

Device Address 

 

 

1 to 255

40401    

U16 

Units 

 

 

 

1 to 3 

 

40402    

U16 

Application Type    

 

0-10

40403    

U16 

Volume Units  

 

 

0 to 6 

40404   

U16 

Decimal Place 

 

 

0 to 3

40405   

U16 

Max Distance 

 

 

0 to 10364 mm

40406    

U16 

Full Distance  

 

 

0 to 10364 mm

40407    

U16 

Empty Distance    

 

0 to 10364 mm 

40408   

U16 

Sensitivity 

 

 

0 to 100

40409 

 U16 

Pulses 

   0 

to 

20

40410 

 U16 

Blanking 

   0 

to 

10364 

mm

40411 

  reserved 

  

40412 

 U16 

Averaging   0 

to 

100

40413   

U16 

Filter Window 

 

 

0 to 10364 mm

40414   

U16 

Out of Range Samples 

 

0 to 255

40415   

U16 

Sample Rate 

 

 

50 to 1000 msec.

40416   

U16 

Multiplier 

 

 

1 to 1999

40417   

S16 

Offset 

 

 

 

+/- 10364 mm

40418-40420 

 reserved 

   

40421   

S16 

RTD Offset (0C) 

 

 

-100 to 100

40422     

U16 

Float Window 

 

 

0 to 1000 mm 

40423     

U32 

Top Float Offset 

 

 

+/- 10364 mm

40424     

U32 

Bottom Float Offset  

 

+/- 10364 mm

40425     

U32 

Gain Offset 

 

 

0 to 255

40426-40435 

 

 

 reserved 

   

40436-40437    U32 

Parameter 1 Data   

 

0 to 100000 mm 

40438-40439    U32 

Parameter 2 Data   

 

0 to 100000 mm  

40440-40441    U32 

Parameter 3 Data    

 

0 to 100000 mm

40442-40443    U32 

Parameter 4 Data   

 

0 to 100000 mm 

40444-40445    U32 

Parameter 5 Data   

 

0 to 100000 mm

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for MND
































Reviews: