background image

 

 

 

26

5.7  ADDING A SATELLITE UNIT 

 
A pilot unit of type AFC System or Nature System will control up to two remote filter units and three re 
oxygenising units. A pilot unit of type Basic System will control one remote filter unit and two re oxygenising 
units. 
In order to make this configuration a machine of type UC1200-01, UC1200-31 or UC1200-32 is used, joined  
to a machine without control circuit, denominated UC1200-00, identical for all technology versions. The 
electrical connection between the two is all that is needed. 
 
 

5.7.1  Connection of high voltage cables 

 

 

 
 
 
 
 
 
 
 
 
 
 
Before closing the machine, connect the micro switch and power to the fan motor. 
 
 

1)  Remove the grill by pushing the black hatches 

towards the center 

2)  Remove the 4 screws that secure the circuit 

and pull it downwards to extract 

3)  Remove the contact plate fixing screws 
4) Use 

exclusively

 special high voltage supplied 

with the machine. Two cables (red and blue) 
are used for all systems, whereas Nature 
System and Basic System have an additional 
black cable.  

5)  Insert the special cables, fitted with appropriate 

sheet, through the hole labelled EAT OUT of 
the contact plate 

6)  Connect the high voltage cables to the red 

isolators of the circuit plate, matching the 
colours of cables (red to red, blue to blue, and if 
applicable, - black to green) . 

7)  Open the remote unit (satellite) as described 

above (point 1, 2 and 3) 

8)  Pass the cables with sheet through the hole 

EAT IN of the contact plate 

9)  Connect the high voltage cables to the red 

isolators as already done with the pilot unit 

10) In case a second satellite is to be fitted, repeat 

the procedure as described above, using a new 
sheet with high voltage cables, making an 
electrical bridge between satellite unit 1 and 
satellite unit 2  

 

ATTENTION : the special high voltage cables 
and their accessories are critical for function 
and safety, and must under no circumstances 
be substituted with inferior products. They must 
only be connected to the red isolators of the 
circuit boards. 
 

Circuit

Contact plate 

Feb

. 12

Automatikprodukter 

Summary of Contents for UC1200



























































Reviews: