background image

FBL2360 Brushless DC Motor Controller Datasheet 

1

FBL2360

RoboteQ’s FBL2360 is a features-packed, high-current, dual 
or single channel controller for brushless DC motors. The 
controller can operate in one of several modes in order to 
sense the rotor position and sequence power on the motor’s 
3 windings in order to generate smooth continuous rotation. 
The controller also uses the Hall sensor and/or Encoder 
information to compute speed and measure travelled distance 
inside a 32-bit counter. The motors may be operated in open 
or closed loop speed mode, position mode or in torque mode. 

The FBL2360 features several Analog, Pulse and Digital I/
Os which can be remapped as command or feedback inputs, 
limit switches, or many other functions. The FBL2360 accepts 
commands received from an RC radio, Analog Joystick, 
wireless modem, or microcomputer. For mobile robot 
applications, the controller’s two motor channels can either be 
operated independently or mixed to move and steer a vehicle. 
Using CAN bus, up to 127 controllers can be networked at up 
to 1Mbit/s on a single twisted pair.

Numerous safety features are incorporated into the controller to 
ensure reliable and safe operation. The controller’s operation can 
be extensively automated and customized using Basic Language 
scripts. The controller can be configured, monitored and tuned 
in real-time using a RoboteQ’s free PC utility. The controller can 
also be reprogrammed in the field with the latest features by 
downloading new operating software from Roboteq.

Applications

• 

Automatic Guided Vehicles

• 

Small Electric Vehicles, Electric Bikes

• 

Terrestrial and Underwater Robotic Vehicles

• 

Police and Military Robots

• 

Hazardous Material Handling Robots

• 

Balancing Robots

• 

Telepresence Systems

• 

Animatronics

Key Features

• 

USB, Serial, 0-5V Analog, or Pulse (RC radio) command 

modes

• 

One RS232 serial port

• 

CAN bus interface up to 1Mbit/switch multiple protocol 

support

• 

RS485

• 

Optional Ethernet interface

• 

Auto switch between Serial, USB, CAN, Analog, or 

Pulse based on user-defined priority

• 

Built-in dual 3-phase high-power drivers for two 

brushless DC motor at up to 60A

• 

Output channels can be paralleled in order to drive a 

single motor at up to 120A

• 

Multiple Motor Operating mode 

-  Trapezoidal with Hall Sensors 
-  Sinusoidal with Encoders 
-  Sinusoidal with Hall Sensors

• 

Support for absolute angle encoders

• 

sin/cos analog

• 

SSI (A & T version)

• 

Resolver (A & T version)

• 

Field Oriented Control in Sinusoidal modes

• 

Full forward & reverse motor control. Four quadrant 

operation. Supports regeneration

• 

Operates from a single 10V-60V power source

• 

STO - Safe Torque Off support (T-version) - Certification 

No. M6A 104504 0001 Rev. 00

• 

Design compliant/approval UL 61800-5-1

• 

Programmable current limit up to 60A (120Aon single 

channel version) per motor for protecting controller, 
motor, wiring and battery.

• 

Separate connector for Hall Sensors

• 

Accurate speed and Odometry measurement using 

Hall Sensor or Encoder data

Advanced Features  

2 x 60A or 1 x 120A  

Brushless DC  

Motor Controller  

with USB and CAN

1

FBL2360_1691-21588-0001-D-0720

Summary of Contents for RoboteQ FBL2360A





















Reviews: