background image

 

 

а 

б 

Pic. 3. Manual unblocking of the carriage 

!

 

In the process of unblocking there can be uncontrolled movement of doors:  
- if the door spring are loose or broken; 
- if the doors are not balanced; 
- if the doors are opened manually the carriage can collide with the drive (during build-

ing works limit the doors run in the opening direction); 

- in the unblocked position doors can be moved only with medium speed!

 

4.2.  Installation of the drive on the rail 

To install the drive on the rail (view B, Pic. 2) follow the instruction: 

 

Connect with slight push the rail end 4 and the drive 1 matching the aperture in the star 
wheel  and  the  drive  shaft.  The  drive  must  be  carefully  installed  on  the  rail.  Little  force 
should be applied for not to damage the drive or spoil its exterior outlook.  

 

Fix the rail to the drive with two U-shaped brackets 9, then tighten them with four nuts 17. 

4.3.  Rail fixing to the wall above the doors 

To fix the rail to the wall above the doors (view C, Pic. 2) follow the instruction: 

 

Define the positioning of the fixing bracket of the rail 8 on the wall above the doors. In the 
highest  point  of  the  doors  movement  at  the  opening  position  the  top  end  of  door  curtain 
must be at least 50 mm lower than the horizontal bottom end of the rail.  

 

Adjust the fixing bracket of the rail 8 at the chosen place on the wall in the horizontal posi-
tion in the middle of the doors using three dowels. If the bracket cannot be positioned in 
the  middle  of  the  doors,  it  must  be  installed  at  a  distance  approximately  100mm  to  the 
right or to the left from the middle of the doors. Use the dowels suitable for the material 
and wall thickness.  

 

Connect the rail with the drive and the fixing bracket of the rail 8 using two bolts 13 and 
two nuts 17. 

 

4.4.  Rail fixing to the ceiling 

To fix the rail to the ceiling follow the instruction: 

 

Fix the U-shaped bracket of the rail 10 (view D, Pic. 2) and the bent fixing strip 22 on the 
rail near the drive using two bolts 14 and two nuts 18.  
If  the  distance  from  the  rail  to  the  ceiling  is  5…130mm  one  fixing  P-shaped  strip  is  used 
(Pic. 2). 
If  the  distance  from  the  rail  to  the  ceiling  is  130…350mm  two  fixing  Z-shaped  strips  are 
used (in this case there should be two additional fixing strips which are not included in the 
scope of supply).  

!

 

Depending  on  the  fixing  technique  choose  the  most  appropriate  apertures  on  the 
bent fixing strip. It is acceptable to cut off the unnecessary part of the fixing strip. 

!

 

The rail with the drive can be installed directly on the  ceiling. In this case the dis-
tance from the rail to the ceiling must be 5 mm.   

Summary of Contents for ASG1000/3KIT
























Reviews: