AMT Datasouth ACCEL-6300 User Manual Download Page 154 | Manualshive

Page: 154 / 257

background image

User's Guide

Bottom-Feed Tractors A-3

Accessing the Bottom-Feed Tractors

There are pop-down supports on the bottom
of the printer that extend to lift up the front
of the printer. This allows easier access to
the bottom-feed tractors.

To use the pop-down supports, lift up the
front edge of the printer until the pop-down
supports are fully extend. Then, lower the
front edge of the printer. The pop-down
supports will lock into place and support
the weight of the printer. You are now
ready to load paper in the bottom-feed
tractors.

To retract the pop-down supports after you
load paper, just lift up the front edge of the
printer again. This time the pop-down sup-
ports will unlock and retract into the holes
on the bottom of the printer.

POP- DOWN

SUPPORT

TRACTOR

Figure A-3. Raising and Lowering the Printer

User's Guide

Bottom-Feed Tractors A-3

Accessing the Bottom-Feed Tractors

There are pop-down supports on the bottom
of the printer that extend to lift up the front
of the printer. This allows easier access to
the bottom-feed tractors.

To use the pop-down supports, lift up the
front edge of the printer until the pop-down
supports are fully extend. Then, lower the
front edge of the printer. The pop-down
supports will lock into place and support
the weight of the printer. You are now
ready to load paper in the bottom-feed
tractors.

To retract the pop-down supports after you
load paper, just lift up the front edge of the
printer again. This time the pop-down sup-
ports will unlock and retract into the holes
on the bottom of the printer.

POP- DOWN

SUPPORT

TRACTOR

Figure A-3. Raising and Lowering the Printer

«
...
152
153
154
155
156
...
»

Summary of Contents for ACCEL-6300


































































































































































































































































Reviews:

No comments

Related manuals for ACCEL-6300

Brand: D-Link Pages: 38

Epress EtherNetwork DP-301P+

Brand: D-Link Pages: 2

Brand: Samsung Pages: 322

Brand: Samsung Pages: 340

Brand: Samsung Pages: 349

Brand: Samsung Pages: 330

Brand: Samsung Pages: 315

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 232

Brand: Samsung Pages: 42

SCX-6545N Series

Brand: Samsung Pages: 468

Brand: Samsung Pages: 196

SCX4521F - B/W Laser - All-in-One

Brand: Samsung Pages: 120

Brand: Xerox Pages: 310

Brand: Xante Pages: 21

Brand: Printek Pages: 34

Brand: WANHAO Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands