AMT Datasouth ACCEL-6300 User Manual Download Page 124 | Manualshive

Page: 124 / 257

background image

User's Guide

Solving Problems 6-7

Understanding Warnings

These messages appear to warn you of special printer conditions.

This warning appears each time you turn on or reset the printer to notify
you that the printer is preparing for normal operation. When the warning
disappears, the printer is ready to print.

Corrective action:

None.

This warning appears when you press the Print Density button to access
the print density adjustment scale, but automatic forms thickness detec-
tion is disabled.

Corrective action:

To enable automatic forms thickness detection, set

the PH GAP parameter on the Setup menu to

Auto

. Then, when you

press the Print Density button, the print density adjustment scale will
appear.

This warning appears when the printer is unable to properly detect paper
in the printer.

Corrective action:

First, try cleaning the platen as described in

Clean-

ing the Platen and Bail Rollers

in the

Cleaning and Maintenance

section of this guide. If the warning recurs after you clean the platen, re-
calibrate the paper sensor as described in

Re-Calibrating the Paper

Sensor

later in this section.

RUN PCALIB TEST

MANUAL PHGAP SET

INITIALIZING....

User's Guide

Solving Problems 6-7

Understanding Warnings

These messages appear to warn you of special printer conditions.

This warning appears each time you turn on or reset the printer to notify
you that the printer is preparing for normal operation. When the warning
disappears, the printer is ready to print.

Corrective action:

None.

This warning appears when you press the Print Density button to access
the print density adjustment scale, but automatic forms thickness detec-
tion is disabled.

Corrective action:

To enable automatic forms thickness detection, set

the PH GAP parameter on the Setup menu to

Auto

. Then, when you

press the Print Density button, the print density adjustment scale will
appear.

This warning appears when the printer is unable to properly detect paper
in the printer.

Corrective action:

First, try cleaning the platen as described in

Clean-

ing the Platen and Bail Rollers

in the

Cleaning and Maintenance

section of this guide. If the warning recurs after you clean the platen, re-
calibrate the paper sensor as described in

Re-Calibrating the Paper

Sensor

later in this section.

RUN PCALIB TEST

MANUAL PHGAP SET

INITIALIZING....

«
...
122
123
124
125
126
...
»

Summary of Contents for ACCEL-6300


































































































































































































































































Reviews:

No comments

Related manuals for ACCEL-6300

Brand: Samsung Pages: 347

SCX 6555N - MultiXpress Mono Multifunction

Brand: Samsung Pages: 180

SCX-4300 - SCX 4300 B/W Laser

Brand: Samsung Pages: 18

SCX-4521FG - B/W Laser - All-in-One

Brand: Samsung Pages: 215

SCX 6320F - B/W Laser - All-in-One

Brand: Samsung Pages: 332

SCX 4828FN - Laser Multi-Function Printer

Brand: Samsung Pages: 248

SCX 4725FN - B/W Laser - All-in-One

Brand: Samsung Pages: 253

ML 2851ND - B/W Laser Printer

Brand: Samsung Pages: 179

ML 2510 - B/W Laser Printer

Brand: Samsung Pages: 84

ML 1740 - B/W Laser Printer

Brand: Samsung Pages: 152

ML 1630 - B/W Laser Printer

Brand: Samsung Pages: 142

ML 1630 - B/W Laser Printer

Brand: Samsung Pages: 82

Brand: Samsung Pages: 2

Brand: Samsung Pages: 384

Lazett Combo SCX-4216F

Brand: Samsung Pages: 135

Brand: Samsung Pages: 414

SCX 6555N - MultiXpress Mono Multifunction

Brand: Samsung Pages: 112

scx-4100 series

Brand: Samsung Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands