manualshive.com logo in svg

AMT Datasouth ACCEL-6300, User Manual

The AMT Datasouth ACCEL-6300 User Manual is a comprehensive guide that allows users to effortlessly operate and optimize their ACCEL-6300 printer. A must-have companion for troubleshooting and maintenance, this manual is available for free download from our website, ensuring convenient access to vital information without any hassle.

Share
Download
background image

User's Guide

5-8  Cleaning and Maintenance

Inspecting Printer Parts

You should occasionally inspect printer components so you can prevent
problems before they occur.  If some component appears to be damaged
or worn, contact your service representative for a replacement part.

,

Caution:

  Before starting your inspection, be sure to turn off the

printer.

Figure 5-8.  Inspecting the Printer, Front

‰

PLATEN

The surface should be dull--not shiny.
Look for dents or flaws in the rubber
surface.

‰

BAIL AND BAIL ROLLERS

Look for stiffness or binding in move-
ment.  Look for dents or flaws in the
rubber surface of the rollers.

‰

PRINTHEAD

Look for bent wires or any visible
signs of wear.

‰

CHASSIS

Look for obstructions in the carriage
path.  Remove any dust, paper fibers,
or other foreign matter from inside
the printer.

‰

PULLEYS AND DRIVE BELTS

Look for looseness or visible
damage.

‰

RIBBON CARTRIDGE

Look for worn fabric.

User's Guide

5-8  Cleaning and Maintenance

Inspecting Printer Parts

You should occasionally inspect printer components so you can prevent
problems before they occur.  If some component appears to be damaged
or worn, contact your service representative for a replacement part.

,

Caution:

  Before starting your inspection, be sure to turn off the

printer.

Figure 5-8.  Inspecting the Printer, Front

‰

PLATEN

The surface should be dull--not shiny.
Look for dents or flaws in the rubber
surface.

‰

BAIL AND BAIL ROLLERS

Look for stiffness or binding in move-
ment.  Look for dents or flaws in the
rubber surface of the rollers.

‰

PRINTHEAD

Look for bent wires or any visible
signs of wear.

‰

CHASSIS

Look for obstructions in the carriage
path.  Remove any dust, paper fibers,
or other foreign matter from inside
the printer.

‰

PULLEYS AND DRIVE BELTS

Look for looseness or visible
damage.

‰

RIBBON CARTRIDGE

Look for worn fabric.

Summary of Contents for ACCEL-6300


































































































































































































































































Reviews:

No comments

Related manuals for ACCEL-6300

Canon Color imageCLASS MF8580Cdw Getting Started Manual preview
Color imageCLASS MF8580Cdw
Brand: Canon Pages: 36
Canon Color imageCLASS MF8580Cdw Settings Manual preview
Color imageCLASS MF8580Cdw
Brand: Canon Pages: 20
Canon Color imageCLASS MF8280Cw Settings Manual preview
Color imageCLASS MF8280Cw
Brand: Canon Pages: 24
Canon Color imageCLASS MF8080Cw Starter Manual preview
Color imageCLASS MF8080Cw
Brand: Canon Pages: 39
Canon Color imageCLASS MF8050Cn Starter Manual preview
Color imageCLASS MF8050Cn
Brand: Canon Pages: 32
Canon Color imageCLASS LBP7660Cdn Quick Setup Manual preview
Color imageCLASS LBP7660Cdn
Brand: Canon Pages: 2
Canon Color imageCLASS 8180c Quick Start Manual preview
Color imageCLASS 8180c
Brand: Canon Pages: 24
Canon CD-300 Printer Manual preview
CD-300
Brand: Canon Pages: 30
Canon C3000 - MultiPASS Color Inkjet Printer Parts Catalog preview
C3000 - MultiPASS Color Inkjet Printer
Brand: Canon Pages: 41
Canon Color imageCLASS MF8170c Specification preview
Color imageCLASS MF8170c
Brand: Canon Pages: 2
Canon Color imageCLASS MF8170c Facsimile Manual preview
Color imageCLASS MF8170c
Brand: Canon Pages: 98
Canon Color imageCLASS MF8170c Instructions Manual preview
Color imageCLASS MF8170c
Brand: Canon Pages: 8
Canon Color imageCLASS MF8080Cw Configuration Manual preview
Color imageCLASS MF8080Cw
Brand: Canon Pages: 46
Canon Color imageRUNNER LBP5360 Release Note preview
Color imageRUNNER LBP5360
Brand: Canon Pages: 3
Canon RP10 User Manual preview
RP10
Brand: Canon Pages: 37
Keeler Vantage Plus Instructions Manual preview
Vantage Plus
Brand: Keeler Pages: 25
Canon imageRUNNER ADVANCE C350iF Service Manual preview
imageRUNNER ADVANCE C350iF
Brand: Canon Pages: 102
Canon imageRUNNER ADVANCE C2230 Manual preview
imageRUNNER ADVANCE C2230
Brand: Canon Pages: 12

Brands by name

Popular brands

Load more brands