Ammann AV 70 X Operating Manual Download Page 85

Page: 85 / 162

AV 70 X

406007

8400 kg

(18 520 lb)

Lmin = 5 m

2x min 2100 kg

(2x min 4630 lb)

Lmin = 5 m

2x min 2100 kg

(2x min 4630 lb)

400143

400144

OPERATION MANUAL

2.8.1. How to load the Machine

Use loading ramps or a crane to load the Machine on its trans-

porting vehicle.
For loading with crane the Machine is fitted with lifting lugs.

Observe safety regulations when load-

ing and unloading!
Use the crane of sufficient loading

capacity!
Use corresponding and unbroken rig-

ging of sufficient loading capacity!
The Machine must be tied to the lifting

lugs on the Machine!
Only a trained person (slinger) may carry

out the tying of the Machine!
Keep off the area beneath the hanging

load!

Before lifting, the Machine joint must be

secured against slight turning.

How to secure the joint:

Dismantle the arm (1).

Secure the arm with pivots (2) and safety pins locks (3).

Summary of Contents for AV 70 X



































































































































































Search results

Summary of Contents for AV 70 X

Reviews:

Related manuals for AV 70 X

Brands by name

Popular brands

Ammann AV 70 X, Operating Manual

Search results

Summary of Contents for AV 70 X

Reviews:

Related manuals for AV 70 X

Brands by name

Popular brands