Ammann AV 70 X Operating Manual Download Page 59

Page: 59 / 162

AV 70 X

400116A

400125

400126

F16

F17

400601

OPERATION MANUAL

Cabin fuse (28)

F15 - 30 A

cabin wiring

The lever (A), when shifted out, can be arrested in any position.

Always replace the fuses with the ones of

identical value!

Diagnostics socket (29)

It is used to check and set the control units’ parameters via exter-

nal computer units (notebook).

Mounting socket (30)

It is used to connect auxiliary inspection lamp (12V).

Steering wheel positioning (31)

It is used to facilitate boarding and leaving the Machine by its

operator.
Release lever (A) to position the steering wheel in the direction

away from the column axis towards a dashboard.

F16, F17 - 125A

Heating of the engine

Summary of Contents for AV 70 X



































































































































































Search results

Summary of Contents for AV 70 X

Reviews:

Related manuals for AV 70 X

Brands by name

Popular brands

Ammann AV 70 X, Operating Manual

Search results

Summary of Contents for AV 70 X

Reviews:

Related manuals for AV 70 X

Brands by name

Popular brands