Ammann AV 70 X, Operating Manual

Page: 156 / 162

150 AV 70 X
3.8. Attachments
A1 Clicker (course light interrupter)
A2 LH cluster
A3 RH cluster
A4 Travel electronics
A5 Travel controller
A6 Time relay
B1 Fuel level float
B3 Pressure sensor in water tank
B4 Engine RPM sensor
B5 Drum speed sensor
C1 Interference filter
E1,2 Front contour lights
E3,4 Rear lights
E5,6 Front headlamps
E7,8 Rear headlamps
E9,10 Left traffic-indicator lights
E11,12 Right traffic-indicator lights
E13,14 Auxiliary headlamps front
(optional)
E15,16 Auxiliary headlamps rear
(optional)
E17 Hazard beacon (optional)
E18,19 Brake (stop) lights
E20 Cabin lighting
E21 Car make lighting (optional)
F1-17 Cut-out fuses
G1 Battery
G2 Alternator
H1 Dipped light indicator lamp
H2 Distance light indicator lamp
H3 Loud horn
H4 Acoustic warning indicator
H5 Backing horn (optional)
K1 Contactor
K2-19 Auxiliary relay
K20 Glowing contactors
K22 Auxiliary relay
M1 Engine starter
M2 Sprinkling motor
M3 Sprinkling motor
M4 Front wiper
M7 Windscreen washer
M9,10,11 Fans
Q1 Battery disconnector
R1 Sprinkling interval potentiome-
ter
R2 Speed potentiometer
R3 Resistor
R4, 5 Engine preheating
S1 Ignition box
S2 Combined switch
S2.1 Switch for contour lights and
headlights
S2.2 Distance / dipped lights switch
S2.3 Light horn switch
S2.4 Loud horn pushbutton
S2.5 Traffic-indicator lights switch
S3 Rear headlamp switch
S4 Warning lights switch
S5 Auxiliary lights switch (optional)
S6 Hazard beacon switch (optional)
S7 Brake pressure switch
S8 Switch for hydraulics filter fou-
led
S9 Switch for air filter fouled
S10 Engine lubrication pressure
switch
S11 Engine overheating switch
S12 Hydraulic oil overheating switch
S13 Float – water in fuel filter
S14 Backing horn switch
S15 Neutral switch
S16 Emergency brake pushbutton
S18 Constant speed or engine over-
load switch
S19 Vibration automatics switch
S20 Smooth start or smooth stop
pushbutton
S21 Seat switch
S22 Vibration pushbutton (red) on
LH travel lever
S23 Vibration pushbutton (red) on
RH travel lever
S24 Sprinkling pushbutton
S25 Sprinkling pumps switch
S26 Vibration amplitude switch
S27 Front / both / rear vibration
selector switch
S28 LH (yellow) pushbutton on LH
travel lever – CRAB left
S29 RH (yellow) pushbutton on LH
travel lever – CRAB right
S30 LH (yellow) pushbutton on RH
travel lever – CRAB left or edge
cutter upward
S31 RH (yellow) pushbutton on RH
travel lever – CRAB right or edge
cutter downward
S32 Front wiper switch
S34 Spaeyer pushbutton
S35 Fan switch
S36 Air conditioner switch (optional)
S38 Float in hydraulic oil tank
S39 CRAB resetting pushbutton
S40,41 CRAB position switches
S42 Hydraulics temperature switch
S44 Air conditioner overpressure
fuse (optional)
S45 Switch of scraper watering
(optional)
X1 Mounting socket
X2 Diagnostics socket
X3-4 Connection terminals
X5-64 Interface connectors
Y1 Engine stop solenoid
Y3 Brake valve
Y4 Back drive valve
Y5 Rearward drive valve
Y8 Vibration low amplitude valve
Y9 Vibration high amplitude valve
Y10 Front drum vibration valve
Y11 Rear drum vibration valve
Y12 CRAB left valve
Y13 CRAB right valve
Y14 Relief valve
Y15 Edge cutter upward valve
(optional)
Y16 Edge cutter downward valve
(optional)
Y17 Air conditioner compressor
clutch magnet (optional)
Y18 Solenoid valve of the edge
cutter watering (optional)
Wiring Diagram
Legend: