Amico Gooseneck Assembly Instructions Manual Download Page 8

Page: 8 / 20

Amico Accessories Inc.

Connecting Powered Gooseneck to Roll Stand Post

1. Use #2 Phillips head screwdriver, place the

POWERED GOOSENECK

with

TABLET HEAD MOUNT

on top of the

TABLET

HEAD MOUNT

and secure with 3x

GOOSENECK HW-KIT SCREWS

(Figure 1)

NOTE:

Pass the cable through the

TABLET HEAD MOUNT

top open channel as shown below. Always align the

TABLET HEAD MOUNT

cable channel with

GOOSENECK

mount plate slot cut as shown in below.

Figure 2

Section 3: Assembly

Figure 1

X-GOSNECK-P_ SCREWS

CABLE

[H-FHMS-632-38-P]

X-GOSNECK-P_]

TABLET HEAD MOUNT

[

[X-MON-DISK-LNG]

POWERED GOOSENECK

CABLE END WITH

USB TYPE A

with mounting plate slot

DETAIL A

Always Align cable channel

CABLE

X-GOSNECK-P_SCREWS

[H-FHMS-632-38-P]

TABLET HEAD MOUNT

[X-MON-DISK-LNG]

POWERED GOOSENECK

[X-GOSNECK-P_]

CABLE END WITH

USB TYPE A

TABLET HEAD MOUNT

[X-MON-DISK-LNG]

X-GOSNECK-NP SCREWS

[H-FHMS-632-38-P]

NON POWERED GOOSENECK

[

X-GOSNECK-NP]

TABLET MOUNT

[X-TB-MNT-HG]

DETAIL A

Always Align cable channel

with mounting plate slot

Always align cable

channel with

mounting plate slot

DETAIL A

Summary of Contents for Gooseneck





















Search results

Summary of Contents for Gooseneck

Reviews:

Related manuals for Gooseneck

Brands by name

Popular brands

Amico Gooseneck, Assembly Instructions Manual

Search results

Summary of Contents for Gooseneck

Reviews:

Related manuals for Gooseneck

Brands by name

Popular brands