Amico Gooseneck Assembly Instructions Manual Download Page 18

Page: 18 / 20

Amico Accessories Inc.

Troubleshooting Guide

Symptom

Solution

Roll Stand is difficult to move

Check to ensure all casters are in an unlocked position (levers up). If any

problem persists after troubleshooting, please contact Amico Accessories at

1.877.264.2697 or [email protected].

Roll Stand moves when it should not

Check to ensure all casters are in an locked position (levers down). If any

problem persists after troubleshooting, please contact Amico Accessories at

1.877.264.2697 or [email protected].

Tablet is drooping

Tighten tablet holder mount on ball-joint by turning the black wing-nut

clockwise. If any problem persists after troubleshooting, please contact Amico

Accessories at 1.877.264.2697 or [email protected].

Handle is loose

Ensure 2x screws are tight, using a #2 Phillips head screwdriver. If any

problem persists after troubleshooting, please contact Amico Accessories at

1.877.264.2697 or [email protected].

Basket is loose

Ensure 4x screws are tight, using a 3/16" (47.6 mm) Hex key. If any problem

persists after troubleshooting, please contact Amico Accessories at 1-877-264-

2697 or [email protected].

Section 4: Troubleshooting, Maintenance and
Product Classification

Preventative Maintenance

It is recommended that once every

three (3) months

, all bolts and screws are checked to ensure that they are tight.

Visually inspect product for signs of damage based on degree of usage.

Cleaning

WARNING:

THE CLEANING CHEMICALS AND METHODS BELOW ARE NOT MEANT FOR INFECTION CONTROL. IT

SHALL BE THE RESPONSIBILITY OF THE FACILITY, CLINIC, HOSPITAL OR THE INFECTION CONTROL OFFICER TO

SANITIZE THE EQUIPMENT.

WARNING:

PLEASE DO NOT SPRAY ANY CHEMICAL DIRECTLY ONTO RS MODELS. APPLY ONTO A SOFT CLOTH AND

WIPE CLEAN TO PREVENT CHEMICALS GETTING INTO THE INTERNAL COMPONENTS OF RS MODELS.

This product can be cleaned with most mild non-abrasive solutions commonly used in the hospital environment

(e.g. diluted bleach, ammonia, alcohol). The surface finish will be permanently damaged by strong chemical and

solvents such as acetone and trichloroethylene. Steel wool or other abrasive material should never be used. Damage

caused by the use of unapproved substances or processes will not be warranted. It is recommended that you test any

cleaning solution on a small area of the RS model that is not visible to verify compatibility. Never submerge the RS

model and do not allow liquids to enter. Wipe any cleaning agents immediately using a water-dampened cloth. Dry

thoroughly after.

No Acetone

Acetone is a colorless, mobile,

flammable liquid

No Trichloroethylene

Trichloroethylene is a chlorinated

hydrocarbon commonly used as an

industrial solvent

Acetone

Trichloroethylene

Figure 1

Figure 2

Summary of Contents for Gooseneck





















Search results

Summary of Contents for Gooseneck

Reviews:

Related manuals for Gooseneck

Brands by name

Popular brands

Amico Gooseneck, Assembly Instructions Manual

Search results

Summary of Contents for Gooseneck

Reviews:

Related manuals for Gooseneck

Brands by name

Popular brands