background image

6

CAUTION: IF BUILDING COLD WATER SUPPLY HAS A BACK-FLOW

PREVENTER, CHECK VALVE OR WATER METER WITH CHECK 

VALVE, PROVISIONS FOR THERMAL EXPANSION OF WATER IN 

THE HOT WATER SYSTEM MUST BE PROVIDED.

FIGURE 3.

CIRCULATING RETURN LINE CONNECTIONS

TEMPERED WATER LOOP, IF USED, CONNECT TO POINT "A".  

STORED TEMPERATURE WATER LOOP, IF USED, CONNECT TO 

COLD WATER INLET

WARNING

TEMPERATURE SETTING SHOULD NOT EXCEED SAFE 

USE TEMPERATURE AT FIXTURES.  SEE TEMPERATURE 

REGULATION ON PAGE 11.  IF HIGHER PREHEAT 

TEMPERATURES ARE NECESSARY TO OBTAIN 

ADEQUATE BOOSTER OUTPUT, ADD AN ANTI-SCALD 

VALVE FOR HOT WATER SUPPLIED TO FIXTURES.

SINGLE TEMPERATURE

VENTING

 WARNING

THE INSTRUCTIONS IN THIS SECTION ON VENTING MUST BE 

FOLLOWED TO AVOID CHOKED COMBUSTION OR RECIRCULATION 

OF FLUE GASES.  SUCH CONDITIONS CAUSE SOOTING OR RISKS 

OF FIRE AND ASPHYXIATION.

This water heater must be protected from freezing downdrafts.

Remove all soot or other obstructions from the chimney that will retard 

a free draft.

Type B venting is recommended with these water heaters. 

This water heater must be vented in compliance with all local codes, the 

current edition of the National Fuel Gas Code, ANSI Z223.1/NFPA 54, 

and with the Category I Venting Tables.

In Canada, venting shall conform to the requirements of the current 

edition of the CAN/CSA B149.1-00 installation code.

If any part of the vent system are exposed to ambient temperatures below 

35 degrees F (2 degrees C) it must be insulated to prevent condensation.

•  Do not connect the heater to a common vent or chimney with solid 

fuel burning equipment.  This practice is prohibited by many local  

building codes as is the practice of venting gas fired equipment to 

the duct work of ventilation systems.

•  Where  a  separate  vent  connection  is  not  available  and  the  vent 

pipe from the heater must be connected to a common vent with an 

oil burning furnace, the vent pipe should enter the smaller common 

vent or chimney at a point above the large vent pipe.

FIGURE 2.

VENT CONNECTION

Vent connections must be made to an adequate stack or chimney. Size 

and install proper size vent pipe.  Do not reduce pipe size to less than 

that of the blower outlet.

Horizontal runs of vent pipe must have a minimum upward slope toward 

the chimney of 1/4 inch per foot (2cm per meter).  Dampers or other 

obstructions must not be installed in between the heater and the blower.  

Be sure that the vent pipe does not extend beyond the inside wall of 

the chimney.

Where a continuous or intermittent back draft is found to exist, the 

cause must be determined and corrected.  A special vent cap may be 

required.  If the back draft cannot be corrected by the normal methods or 

if a suitable draft cannot be obtained, a blower type flue gas exhauster 

must be employed to assure proper venting and correct combustion.

MIXING VALVE APPLICATION FOR TWO TEMPERATURE WATER

VACUUM RELIEF

       VALVE

*INSTALL PER 

LOCAL CODES.

Summary of Contents for BBCN375T754NV 100 Series

























Reviews: