manualshive.com logo in svg

American Dryer Corp. AD30 2R Series, Service Manual, Page: 13 / 24

Share
Download
American Dryer Corp. AD30 2R Series Service Manual Download Page 13

450370 - 2

www.adclaundry.com

13

4. Remove the screws securing the front panel to the dryer

at the top and bottom of the panel.

5. Gently remove the top right hand corner of the front panel

assembly from the dryer.

6. Disconnect the main door switch harness at the connector.

TO INSTALL NEW MAIN DOOR GLASS

1. Remove main door assembly from the dryer (follow main

door removal procedure).

2. Lay main door on a flat surface with front of door face

down.

3. Remove glass and clean all old sealant off main door.

This area must be completely cleaned for correct bonding.

4. Apply narrow bead of silicone all around main door area

where glass will rest.

5. Install glass onto door/adhesive and slightly press glass

in place.

IMPORTANT: 

Do not press hard or silicone thickness

between the glass and door will be reduced resulting in
poor bonding.

6. The door assembly should now be put in an area where it

will not be disturbed for at least 24 hours.  Depending on
the conditions, the curing time of the adhesive is 24 to 36
hours.

7. After 24 hour curing period, install main door on dryer by

reversing Step #1.

TO REPLACE FRONT PANEL

1. Discontinue power to the dryer.

2. Follow procedure for removal of main door assembly.

3. Open control (service) door and lint door.

IMPORTANT: 

When removing front panel assembly, be

careful not to damage main door switch wires disconnected
in 

Step #2

.

7. Reverse this procedure for installing the new front panel.

Drive Pulley

(Remove back guard to access assembly)

1. Remove the back guard.

2. Loosen belt then rotate pulley and roll belt out of the

grooves.

3. Loosen setscrews and pull motor pulley out.

NOTE: 

If rust has developed on the shaft, use an emery

cloth to polish the shaft.

4. Reverse procedure for installing the new drive pulley.

NOTE: 

Check tension and alignment of belt before

operating the dryer.

TO REPLACE THE TUMBLER

1. Discontinue power to the dryer.

2. Remove the front panel assembly.

3. Remove center dome by removing four (4) Phillips head

screws.  Then remove setscrew.

4. Grab the basket, pull forward and twist.

5. After replacing tumbler reassemble components into dryer

by reversing Steps #1 through #4.

6. Check belt tension and alignment.

7. Replace the back guard and reestablish power to the dryer.

Summary of Contents for AD30 2R Series

























Reviews:

No comments