background image

  Accu UFO PRO 

                                           Fuse Replacement

The fuse holder located at the rear of the unit above the power cord. Discon-
nect from the main power supply. Insert a standard flat head screw driver in 
to the fuse holder housing, located on the back of the unit. Turn the screw-
driver in counter-clockwise direction to remove the fuse holder. Remove the 
old fuse and discard it, replace the fuse with the same type. Insert the fuse 
back into it’s housing.

  Accu UFO PRO    

 

                             Cleaning

Due to fog residue, smoke, and dust cleaning the internal and external op-
tical  lenses  and  mirror  should  be  carried  out  periodically  to  optimize  light 
output. Cleaning frequency depends on the environment in which the fixture 
operates (I.e. smoke, fog residue, dust, dew). In heavy club use we recom-
mend cleaning on a monthly basis. Periodic cleaning will ensure longevity, 
and crisp output.
1.   Use normal glass cleaner and a soft cloth to wipe down the outside cas- 
 

ing.

2.   Use a brush to wipe down the cooling vents and fan grill.
3.   Clean the external optics and mirror with glass cleaner and a soft cloth  
 

every 20 days.

4.   Clean the internal optics with glass cleaner and a soft cloth every 30-60  
 

days.

5.   Always be sure to dry all parts completely before plugging the unit back  
 

in.

  Accu UFO PRO    

 

                Trouble Shooting

Listed below are a few common problems that you may encounter, with so-
lutions.

No light output from the unit;

1.   Be sure you have connected your unit into a standard 120v wall outlet.  
2.     Be sure the external fuse has not blown. The fuse is located at the rear  
 

 of the unit. 

3.   Be sure the fuse holder is completely and properly seated. 

 
Unit does not respond to sound;

1.     Low frequencies (bass) should cause the unit to react to sound. Tap- 
 

 ping on the microphone, quiet or high pitched sounds may not activate  

 

 the unit.  

2.   Check the Mic setting. It may be set to a lower sensitivity setting. See  
 

 pages 21-22.

  Accu UFO PRO    

                 10 DMX Channel Mode

  Channel     Value 

 

         Function

       7            181 - 190                  AUTO PROGRAM 3    
                     191 - 200                  AUTO PROGRAM 4
                     201 - 210                  AUTO PROGRAM 5
                     211 - 220                  AUTO PROGRAM 6
                     221 - 230                  AUTO PROGRAM 7
                     231 - 240                  AUTO PROGRAM 8
                     241 - 255                  AUTO PROGRAM 9                  
       8                                                   LED SPEED
                         0 - 255                      SLOW - FAST      
       9                                                    STROBING
                           0                             NO FUNCTION
                         1 - 95              STROBING   SLOW - FAST
                       96 - 127                      NO FUNCTION
                     128 - 159        PULSE EFFECT IN SEQUENCES
                     160 - 191                      NO FUNCTION
                     192 - 223    RANDOM STROBING   SLOW - FAST
                     224 - 255                      NO FUNCTION
      10                                  RESET & INTERNAL PROGRAMS
                         0 - 19              NORMAL COLOR CHANGE
                       20 - 79                        NO FUNCTION
                       80 - 84                    ALL MOTOR RESET
                       85 - 87               SCANNER MOTOR RESET
                       88 - 99                        NO FUNCTION
                     100 - 119              INTERNAL PROGRAM 1 
                     120 - 139              INTERNAL PROGRAM 2
                     140 - 159              INTERNAL PROGRAM 3
                     160 - 179              INTERNAL PROGRAM 4
                     180 - 199              INTERNAL PROGRAM 5
                     200 - 219              INTERNAL PROGRAM 6
                     220 - 239              INTERNAL PROGRAM 7                     
                     240 - 255                     SOUND ACTIVE               

American DJ

®

  -  www.americandj.com  - Accu UFO PRO Instruction Manual Page 41

American DJ

®

  -  www.americandj.com  - Accu UFO PRO Instruction Manual Page 42

Summary of Contents for Accu UFO PRO























Reviews: