background image

American DJ

®

  -  www.americandj.com  - Accu UFO PRO Instruction Manual Page 24

American DJ

®

  -  www.americandj.com  - Accu UFO PRO Instruction Manual Page 23

SPEC  

MAIN MENU -

RDMX

  With this function you are able to change the DMX 

address via any DMX controller. This function is factory set 

to “ON” already.

1. Access the main menu by pressing MODE/ESC.
2. Tap the UP button until “

SPEC

” is displayed, press ENTER.

3. Tap the UP button until “

RDNX

” is displayed, press ENTER.

4. Press the UP button to select “

ON

” to activate this function, 

or “

OFF

” to deactivate.

5. Press ENTER to confirm, and “

PASS

” will flash quickly.

6. Press MODE/ESC to return to the main menu.

To use this function follow the instructions: 

To adjust the address of your unit you must first go to the 
address that it is currently set to. From there you can adjust the 
address. First make sure all channels are set to the value of “0”.
1. On your DMX controller set the DMX value of Channel 1 to 
the value “7”.
2. Now set the DMX value of Channel 2 to the value “7” to 
adjust the starting address between 1 and 255. To adjust the 
address between 256 and 511 set Channel 2 to the value “8” .
3. Set the DMX value of Channel 3 to your desired start-
ing address. This will take about 20 seconds before the unit 
accepts the new DMX address. 

EXAMPLE: 

So, if you want the address to be 57, you must first 

set the address that is currently assingned to the unit. The pro-
ceed to set Channel 1 value to “7”, Channel 2 value to “7”, and 
Channel 3 value to “57”. 

2ND EXAMPLE:

 Again, if you want the address to be 420, you 

must first set the address that is currently assingned to the unit.
If you want the set the address to 420, set Channel 1 value to 

 Accu UFO PRO   

 

 

            System Menu  

 Accu UFO PRO   

 

 

            System Menu

vate this function, or “

OFF

” to deactivate this function.

5. Press ENTER to confirm.
6. Press MODE/ESC to return to the main menu.

FLIP

 

This function will reverse the display 180º.

1. Access the main menu.
2. Tap the UP button until “

DISP

” is displayed.

3. Tap the UP button until “

FLIP

” is displayed, press ENTER.

4. Press the UP or DOWN buttons to select either “

ON

” to acti-

vate this function, or “

OFF

” to deactivate this function.

5. Press ENTER to confirm.
6. Press MODE/ESC to return to the main menu.

LOCK

 

With this function you can activate the automatic 

button lock. When this function is activated, the buttons 

will automatically lock 15 seconds after the last press of 

a button. In order to deactivate the button lock, press the 

MODE/ESC button for 3 seconds.

1. Access the main menu.
2. Tap the UP button until “

DISP

” is displayed.

3. Tap the UP button until “

LOCK

” is displayed, press ENTER.

4. Press the UP or DOWN buttons to select either “

ON

” to acti-

vate this function, or “

OFF

” to deactivate this function.

5. Press ENTER to confirm.
6. Press MODE/ESC to return to the main menu.

Summary of Contents for Accu UFO PRO























Reviews: