manualshive.com logo in svg

AMD -K6-2/450 - MHz Processor, Application Note

Share
Download
AMD -K6-2/450 - MHz Processor Application Note Download Page 83

Appendix A

71

23913A/0—November 2000

Embedded AMD-K6™ Processors BIOS Design Guide

Preliminary Information

Appendix A

CPUID 

mnemonic

opcode

description

CPUID

0F A2h

Identify the processor and its feature set

Privilege:

none

Registers Affected:

EAX, EBX, ECX, EDX

Flags Affected:

none

Exceptions Generated: none

The CPUID instruction is an application-level instruction that software executes to
identify the processor and its feature set. This instruction offers multiple functions,
each providing a different set of information about the processor. The CPUID
instruction can be executed from any privilege level. Software can use the information
returned by this instruction to tune its functionality for the specific processor and its
features.

Beginning with the AMD-K6E processor Model 7, all AMD processors support the
CPUID instruction. However, it is still recommended that software verify that the
CPUID instruction is supported. See “Testing for the CPUID Instruction” on page 58
for more information.

The CPUID instruction supports multiple functions. The information associated with
each function is obtained by executing the CPUID instruction with the function
number in the EAX register. Functions are divided into two types: standard functions
and extended functions. Standard functions are found in the low function space,
0000_0000h–7FFF_FFFFh. In general, all x86 processors have the same standard
function definitions. 

Extended functions are defined specifically for processors supplied by the vendor
listed in the vendor identification string. Extended functions are found in the high
function space, 8000_0000h–8FFF_FFFFh. Because not all vendors have defined
extended functions, software must test for their presence on the processor. 

Summary of Contents for -K6-2/450 - MHz Processor



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands