manualshive.com logo in svg

AMD -K6-2/450 - MHz Processor, Application Note

Share
Download
AMD -K6-2/450 - MHz Processor Application Note Download Page 48

36

Model 8/[F:8] Registers

Embedded AMD-K6™ Processors BIOS Design Guide

23913A/0—November 2000

Preliminary Information

Page Flush/Invalidate Register (PFIR)

Models 8/[F:8], 9, and D contain the Page Flush/Invalidate
Register (PFIR) (see Figure 9) that allows cache invalidation
and optional flushing of a specific 4-Kbyte page from the linear
address space. 

The total amount of L1 cache in the processor is 64 Kbytes.
Using this register can result in a much lower cycle count for
flushing particular pages versus flushing the entire cache.
When the PFIR is written to (using the WRMSR instruction),
the invalidation and, optionally, the flushing begins. 

The PFIR register is MSR C000_0088h.

Note: The invalidate and flush operations affect both the L1 and

L2 caches on models 9 and D.

Figure 9.   Page Flush/Invalidate Register (PFIR) (Models 8/[F:8], 9, and D)

LINPAGE Field

This 20-bit field must be written with bits 31:12 of the linear
address of the 4-Kbyte page that is to be invalidated and
optionally flushed from the L1 cache.

PF Bit

If an attempt to invalidate or flush a page results in a page
fault, the processor sets the PF bit to 1, and the invalidate or
flush operation is not performed (even though invalidate
operations do not normally generate page faults). In this case,
an actual page fault exception is not generated. 

If the PF bit equals 0 after an invalidate or flush operation,
then the operation executed successfully. The PF bit must be
read after every write to the PFIR register to determine if the
invalidate or flush operation executed successfully.

LINPAGE

1 0

63

F

/

I

Reserved

Symbol

Description

Bit

LINPAGE

20-bit Linear Page Address

31-12

PF

Page Fault Occurred

8

F/I

Flush/Invalidate Command

0

11

31

12

32

P
F

9 8 7

Summary of Contents for -K6-2/450 - MHz Processor



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands