Altrad BELLE PREMIER 100XT Operator'S Manual Download Page 16

Page: 16 / 70

Maintenance Instructions

%HIRUHVWDUWLQJDQ\PDLQWHQDQFHRUUHSDLUVVWRSHQJLQHRUVZLWFKRႇPRWRUDQGLVRODWHIURPWKHPDLQSRZHUVXSSO\
2QFRPSOHWLRQRIPDLQWHQDQFHFKHFNWKDWWKHPL[HUIXQFWLRQVFRUUHFWO\DQGWKDWDOOJXDUGVDUHFRUUHFWO\¿WWHG

ELECTRIC MOTORS

All portable electric appliances are dangerous if abused. This machine will only operate on one voltage. Check the power supply to

HQVXUHLWFRUUHVSRQGVWRWKHYROWDJHDVVWDPSHGRQWKHPRWRU0DNHVXUHWKDWWKHPRWRULVVZLWFKHGRႇEHIRUH\RXSOXJLWLQWRWKH

power supply.

220-240v

-Always use a Residual Current Device (“RCD”), (earth leakage trip), plugged directly into the 220-240v socket. If using an

extension cable, plug it directly into the RCD.

110v

-When using a portable transformer it must have a minimum output of 6.3kw and be continuously rated.

- DO

NOT

use an extension cable between the transformer and the power supply.

The symbols on the ON/OFF switch are 0=OFF and I=ON in accordance with international standards.

If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its

service agent. (See Wiring Diagram on Page 15.)

EXTENSION CABLES

If you need to use an extension cable it must be no longer than 30 metres (100 feet) in length. The wire section for 220-240v must be
2.5mm

. The wire section for 110v must be 4mm2 on 100XT and 6mm2 on other models. Ensure that the extension cable is

carefully laid out avoiding liquids, sharp edges and places where vehicles might run over it. Unroll it fully or it will overheat and could

FDWFK¿UH0DNHVXUHWKDWDQ\H[WHQVLRQFDEOHFRQQHFWLRQVDUHGU\DQGVDIH

COMBUSTION ENGINES
-

Be aware of exhaust venting directions.

ENGINE OIL

The engine needs a regular oil check.Try not to run low on fuel as this may result in sediment from the bottom of the tank doing
damage to the injector and pump.

5HSDLUVDQGUHFWL¿FDWLRQRISLSHZRUNDQGFRPSRQHQWVDႇHFWHGE\FRQWDPLQDQWVLQIXHO

cannot be accepted as warranty, neither will faults caused or contributed to by the machine running out of fuel.

You may

need to bleed the fuel system free of air before starting.

Select the appropriate engine oil viscosity based on the ambient temperature

DQGXVHWKH6$(6HUYLFH*UDGH9LVFRVLW\&KDUWEHORZ7KLVPDFKLQHLV¿OOHGZLWK6$(:DWWKHIDFWRU\

(QJLQH2LO6SHFL¿FDWLRQV

Use an engine oil that meets or exceeds the following guidelines

DQGFODVVL¿FDWLRQV

Service Categories

API Service Categories CD or higher.

ACEA Service Categories E-3, E-4 and E-5

JASO Service Category DH-1

'H¿QLWLRQV

$3,&ODVVL¿FDWLRQ$PHULFDQ3HWUROHXP,QVWLWXWH

$&($&ODVVL¿FDWLRQ$VVRFLDWLRQGHV&RQVWUXFWHXUV(XURSpHQV

d’automobilies)

JASO (Japanese Automobile Standards Organisation)

DRUM (Removal and Fitment)

7KLVFDQEHLQVWDQWO\UHPRYHGE\XQVFUHZLQJLWFRXQWHUFORFNZLVHLQWKHYHUWLFDOO\XSSRVLWLRQ/LIWWKHGUXPRႇWKHPDFKLQHXVLQJD

fork lift, with the forks under the base of the drum. When replacing make sure that the drum shaft is greased before it is fully
screwed down on to the shoulder of the shaft, ensure the drum is fully screwed down on to the shoulder or damage will occur. Take
care when screwing on the drum, spinning on fast may damage the gearbox.

CLEANING

:LSHRႇDQ\H[WHUQDOPDWHULDO

DO NOT

XVHSHWUROWXUSHQWLQHODFTXHURUSDLQWWKLQQHUGU\FOHDQLQJÀXLGVRUVLPLODUSURGXFWV1HYHU

let any liquids near the engine/motor. Use 1” gravel and clean water to clean the inside of the drum.

- DO

NOT

use bricks etc. as this will damage the drum.

30°F

(22°C)

-4°F

(-20°C)