alphatronics DLM-600 Installer/User Manual Download Page 33 | Manualshive

Page: 33 / 39

background image

DLM-600 installer & user manual Rev. 1.3

16-11-2011

33 / 39

APPENDIX A: INSTALLING THE FLASH TOOL SOFTWARE

To flash new firmware into the DLM-600 a (free) flash tool is available. This flash tool is provided by the
manufacturer of the microprocessor (Renesas).

Installing the flash tool is very simple. Install the fdt_3_06 file (an EXE file) on your computer / laptop.
Use the default values supplied by the manufacturer and complete the full installation. During installation
choose the ‘create a desktop icon’ option. Uncheck the ‘USB drivers’ and ‘AutoUpdate’ when the
following screen appears.

After the software installation has been completed successfully start the Flash Development Toolkit 3.06
Basic. If no desktop icon is created, the program can be found from in

Programs / Renesas

etc.

The following procedure is only necessary if the start the program for the first time. The next time you run
the program all the settings made will be remembered from the last session. After starting the following
screen will appear:

«
...
31
32
33
34
35
...
»

Summary of Contents for DLM-600








































Reviews:

No comments

Related manuals for DLM-600

Brand: Samson Pages: 28

Brand: 3onedata Pages: 3

Brand: 3onedata Pages: 9

Brand: 3onedata Pages: 3

Brand: 3onedata Pages: 3

Brand: 3onedata Pages: 3

Brand: 3onedata Pages: 3

Brand: 3onedata Pages: 7

Brand: ICP DAS USA Pages: 113

Brand: Sungrow Pages: 14

Brand: Senergy Pages: 50

Z3-SBE264-DVR-13

Brand: Z3 Technology Pages: 50

Brand: CYP Pages: 12

Brand: GMI Pages: 9

Brand: Waversasystems Pages: 15

Brand: Oriental motor Pages: 56

Brand: Littfinski Daten Technik Pages: 2

Brand: Green Gear Pages: 222

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands