background image

Page 

43

 to 

52 

Problem

 

Possible cause

 

Solution

 

THE TRI POWER X33 
HE OPERATES 
OFF THE BATTERIES 
EVEN THOUGH MAINS 
POWER IS PRESENT

 

INTERVENTION OF THE 
TRI POWER X33 
HETREAM PROTECTION 
DEVICE 

Restore the protection. 
WARNING: make sure there is no overload or 
short circuit on the TRI POWER X33 HE output. 

THE INPUT VOLTAGE IS 
OUT OF THE ALLOWED 
OPERATING VALUES 
FOR MAINS POWER 

Problem caused by the mains power. Wait for the 
input mains voltage to return within the tolerance 
limits. The TRI POWER X33 HE will return 
automatically to mains operation. 

THE DISPLAY SHOWS 
C01 

THE JUMPER IS 
MISSING FROM THE 
R.E.P.O. CONNECTOR 
(see “FRONT VIEWS OF 
THE TRI POWER X33 
HE”) OR IT IS NOT 
INSERTED CORRECTLY 

Assemble the jumper or make sure that it is 
inserted correctly. 

THE DISPLAY SHOWS 
C02 

MAINTENANCE BYPASS 
ISOLATOR (SWMB) 
CLOSED 

Open the isolator (SWMB) located behind the door. 

THE JUMPER IS 
MISSING FROM THE 
TERMINALS FOR THE 
REMOTE MAINTENANCE 
BYPASS (J2, “VIEWS OF 
THE TRI POWER X33 HE 
CONNECTIONS”) 

Insert the jumper 

THE DISPLAY SHOWS 
ONE OR MORE OF THE 
FOLLOWING CODES: 
A30, A32, A33, A34 
AND THE TRI POWER 
X33 HE DOES 
NOT START UP 

AMBIENT 
TEMPERATURE < 0°C 

Heat the environment, wait for the heat sink 
temperature to rise above 0°C and then start up 
the TRI POWER X33 HE 

FAULT IN HEAT SINK 
TEMPERATURE PROBE 

Activate the maintenance bypass (SWMB), turn the 
TRI POWER X33 HE off and back on again and 
exclude the maintenance bypass. If the problem 
persists, contact the nearest service centre 

THE DISPLAY SHOWS 
ONE OR MORE OF THE 
FOLLOWING CODES: 
F09, F10 

FAULT IN THE INPUT 
STAGE OF THE TRI 
POWER X33 HE 

Activate the maintenance bypass (SWMB), turn the 
TRI POWER X33 HE off and back on again and 
exclude the maintenance bypass. If the problem 
persists, contact the nearest service centre 

PHASE 1 HAS A MUCH 
LOWER VOLTAGE THAN 
THE OTHER TWO 
PHASES. 

Open the SWIN, switch on the TRI POWER X33 
HE from the battery. Wait for the sequence to be 
completed and close the SWIN 

THE DISPLAY SHOWS 
ONE OR MORE OF THE 
FOLLOWING CODES: 
F11, F14, F15, F16, F17, 
L06, L07, L08, L09, L14, 
L15, L16, L17, L18, L19, 
L20, L21, L22

 

ANOMALOUS LOADS 
APPLIED 

Remove the load. Insert the maintenance bypass 
(SWMB), turn the TRI POWER X33 HE off and 
back on again. Exclude the maintenance bypass. If 
the problem persists, contact the nearest service 
centre 

FAULT IN THE INPUT OR 
OUTPUT STAGE OF THE 
TRI POWER X33 HE 

Activate the maintenance bypass (SWMB), turn the 
TRI POWER X33 HE off and back on again. 
Exclude the maintenance bypass. If the problem 
persists, contact the nearest service centre 

THE DISPLAY SHOWS 
ONE OR MORE OF THE 
FOLLOWING CODES: 
F03, F04, F05, A08, A09, 
A10

 

NO CONNECTION ON 
ONE OR MORE PHASES 

Check the connections to the terminals 

INTERNAL PROTECTION 
FUSES ON THE PHASES 
OR ON THE INPUT 
RELAY BROKEN 

Contact the nearest service centre 

Summary of Contents for Tri Power X33 HE






















































Reviews: