Allmatic BIOS1 24V, Manual, Page: 26 / 120

6/20 6-1622400 rev. 8 19/01/2022
ENG
ITA ENG FRA ESP NLD TUR
4.1 - LIST OF TERMINAL BOARDS AND CONNECTORS
Number Name Description
1 - 2 FLASH Flashing light output at 24Vac. Use a flashing light without self flashing card 24Vac 25W max.
3 - 4 OGL Courtesy light / Open automation light output at 24Vac. Use a light 24Vac 25W max. The
functioning of the auxiliary light and its activation time are managed from advanced items
FC . Y . and tc . y .
5 +24VDC +24Vdc accessories power supply. Used for the receiver of the photocells.
6 GND 0Vdc accessories power supply.
WARNING - The control unit supplies up to a maximum of 200 mA (5W) for the accessories
at 24Vdc.
7 +24VDC TX PHOTO +24Vdc accessories power supply. Used for the transmitter of the photocells. This connection
is necessary in case of use of the photocells test. It is possible to enable the photocells test
from the advanced menu tp . h .
8 PE Ground connection.
9 - 10 EDGE Safety edge input (NC contact). Select the type of the used safety edge (mechanical or resistive)
through the advanced menu
ED
.
M
. and the mode of intervention with the advanced menu
ie
.
d
.
WARNING - with DIP EDGE on “ON” the input is disabled.
11 - 18 PH2 - COM Opening photocell input (NC contact). The photocell intervenes at any time during the opening
of the automation system and stops immediately the movement; the automation system will
continue the opening when the photocell beam is freed. In the event of intervention on closure
(parameter Ph.2. = 0), the automation stops and, when the beam is freed, moves on opening.
In the advanced item
Ph
.
2
., it is possible to select the behaviour of the photocell.
WARNING - with DIP PH2 on “ON” the input is disabled.
12 - 18 PH1 - COM Closing photocell input (NC contact). The photocell intervenes at any time during the closing
of the automation system, stops immediately and inverts the movement. The photocell doesn’t
intervene during the opening.
In the advanced item sp . h . it is possible to select the behaviour of the photocell with the
closed automation.
WARNING - with DIP PH1 on “ON” the input is disabled.
13 - 18 STOP - COM Connect the STOP command (NC contact). This input is classified as a safety device; the
opening of the contact stops immediately the automation and it remains blocked up to the
restoring of the state of the input contact.
WARNING -
with DIP STOP on “ON” the input is disabled.
14 - 18 OPEN - COM Connect the button for the OPEN command (NO contact).
15 - 18 CLOSE - COM Connect the button for the CLOSE command (NO contact).
16 - 18 PED - COM Connect the button for the PARTIAL OPENING command (NO contact).
17 - 18 SS - COM Connect the button for the STEP-BY-STEP command (NO contact).
18 COM Common for safety and command inputs.
19 - 18 LS1 - COM Connect the limit switch 1 (NC contact).
20 - 18 LS2 - COM Connect the limit switch 2 (NC contact).
21 ANTENNA Connect the antenna
22 SHIELD Connect the antenna braiding.
23 - 24 MOTOR Connect the motor.
25 - 26 BATTERY CHARGER Connect the battery charger card.
Use the clamp 25 for the POSITIVE pole.
Use the clamp 26 for the NEGATIVE pole.
J3 Connector for the Bluetooth module.
J4 Connector for the external memory.
J5 Connector for the optional R1 card.
J7 Connector for the power supply from the transformer.