Allied Vision Technologies Pearleye P-007 LWIR Technical Manual Download Page 11

Page: 11 / 85

Introduction

Pearleye Technical Manual

V2.2.0

Before operation

We place the highest demands for quality on our cameras.

Target group

This

Technical Manual

is the guide to detailed technical information of the

camera and

is written for experts

Getting started

For a quick guide how to get started read:

How to install a GigE camera

(Bigeye/Pearleye/Goldeye)

Safety warnings

Note



Please read through this manual carefully before operating
the camera.

Caution



Before operating any AVT camera read

safety instructions

and

ESD warnings.

Caution



Electrostatic discharge

The camera contains sensitive electronic components which
can be destroyed by electrostatic discharge.

Use sufficient grounding to minimize the risk of damage.

Summary of Contents for Pearleye P-007 LWIR






















































































Search results

Summary of Contents for Pearleye P-007 LWIR

Reviews:

Related manuals for Pearleye P-007 LWIR

Brands by name

Popular brands

Allied Vision Technologies Pearleye P-007 LWIR, Technical Manual

Search results

Summary of Contents for Pearleye P-007 LWIR

Reviews:

Related manuals for Pearleye P-007 LWIR

Brands by name

Popular brands