background image

 

ii

 

NETZKABEL

 

Das Netzkabel sollte eine maximale Länge von 4,5 Metern, einen Nennwert von mindestens 6 A und 250 V haben, aus HAR-Material 
hergestellt und mit einer gepreßten, IEC 320 entsprechenden, Anschlußverbindung an einem Ende, und am anderen Ende mit einem im 
Land des Endverbrauchers geprüften Stecker ausgestattet sein.

 

MONTAGEANWEISUNGEN

 

VORSICHT: Diese Modelle sind für Betrieb in horizontaler Position entworfen worden.  Das Gerät darf  NICHT OHNE Gebrauch eines 
dafür entworfenen Allied Telesyn-Vertikalmontagegestells in VERTIKALER Position montiert werden.

VORSICHT: Die Entlüftungsöffnungen dürfen nicht versperrt sein und müssen zum Kühlen freien Zugang zur Raumluft haben.

VORSICHT: Die Gummifüße NICHT ENTFERNEN, außer bei Gebrauch des Allied Telesyn-Vertikalmontagegestells.

 

BETRIEBSTEMPERATUR

 

Dieses Produkt wurde für den Betrieb in einer Umgebungstemperatur von nicht mehr als 50˚ C entworfen.

 

ALLE LÄNDER:

 

 Installation muß örtlichen und nationalen elektrischen Vorschriften entsprechen.

 

STRÅLINGSENERGI

 

Dette kommercielle produkt opfylder de krav, der i USA stilles til udstyr af Klasse A.

 

SIKKERHED

 

ELEKTRISKE FORHOLDSREGLER
ADVARSEL: RISIKO FOR ELEKTRISK STØD
For at forebygge ELEKTRISK stød, undlad at åbne apparatet. Der er ingen indre dele, der kan repareres af brugeren. Denne enhed  
indeholder LIVSFARLIGE STRØMSPÆNDINGER og bør kun åbnes af en uddannet og kvalificeret tekniker.  For at undgå risiko for 
ELEKTRISK STØD, afbrydes den elektriske strøm til produktet, før LAN-kablerne monteres eller afmonteres.

FARE UNDER UVEJR
FARE: UNDLAD at arbejde på udstyr eller KABLER i perioder med LYNAKTIVITET.

ADVARSEL: DEN STRØMFØRENDE LEDNING BRUGES TIL AT AFBRYDE STRØMMEN.  SKAL STRØMMEN  TIL 
APPARATET AFBRYDES, tages ledningen ud af stikket.

 

INSTALLATION

 

ELEKTRISK—AUTOMATISK SPÆNDINGSREGULERING
Dette apparat vil automatisk tilpasse sig enhver spænding indenfor de  værdier, der er angivet på etiketten.

ELEKTRISK—KLASSE 1-UDSTYR 
DETTE UDSTYR KRÆVER JORDFORBINDELSE. Stikket skal være forbundet med en korrekt installeret jordforbunden stikkontakt. 
En ukorrekt installeret stikkontakt kan sætte livsfarlig spænding til tilgængelige metaldele.

ELEKTRISK—LEDNING
Anvend ledning af maksimum 4,5 meters længde, med en kapacitet på  minimum 6 amp., 250 v,  bestående af en IEC 320 connector med 
indstøbt HAR ledning i den ene ende og et stik i den anden ende godkendt der er af myndighederne i brugerlandet.

 

INSTRUKTIONER FOR OPSTILLING

 

ADVARSEL: Disse modeller er konstrueret til at betjenes i HORISONTAL position (vandret). VERTIKAL OPSTILLING (lodret) må 
IKKE FORETAGES uden brug af et Allied Telesyn vertikalt monteringsstel konstrueret til dette formål.

ADVARSEL: Ventilationsåbninger må ikke blokeres og skal have fri adgang til den omgivende luft i rummet for afkøling.

ADVARSEL: UNDLAD at fjerne gummisoklerne fra apparatet, med mindre der anvendes et Allied Telesyn vertikalt monteringsstel.

 

BETJENINGSTEMPERATUR

 

Dette apparat er konstrueret til en omgivende temperatur på maksimum 50 grader C.

 

ALLE LANDE:

 

 Installation af produktet skal ske i overensstemmelse med lokal og national lovgivning for elektriske installationer.

 

STRALINGSENERGIE

 

Dit handelsprodukt werd getest en voldoet aan de Amerikaanse vereisten voor een klasse A toestel.

 

VEILIGHEID

 

WAARSCHUWINGEN MET BETREKKING TOT ELEKTRICITEIT
WAARSCHUWING: GEVAAR VOOR ELEKTRISCHE SCHOKKEN
Gelieve het deksel niet te verwijderen, teneinde ELEKTRISCHE schokken te voorkomen. Binnenin bevinden zich geen onderdelen die 
door de gebruiker kunnen worden onderhouden. Dit toestel staat onder GEVAARLIJKE SPANNING en mag alleen worden geopend door 
een daartoe opgeleide en bevoegde technicus. Om het gevaar op ELEKTRISCHE SCHOKKEN te vermijden, moet u het toestel van de 
stroombron ontkoppelen alvorens de LAN-kabels te koppelen of ontkoppelen.

GEVAAR VOOR BLIKSEMINSLAG
GEVAAR: NIET aan toestellen of KABELS WERKEN bij BLIKSEM.

WAARSCHUWING: HET TOESTEL WORDT UITGESCHAKELD DOOR DE STROOMKABEL TE ONTKOPPELEN.
OM HET TOESTEL STROOMLOOS TE MAKEN: de stroomkabel ontkoppelen.

 

INSTALLATIE

 

ELEKTRISCH—AUTOMATISCHE AANPASSING VAN DE SPANNING
Dit toestel past zich automatisch aan elke spanning aan, tussen de waarden op het label vermeld.

Vorsicht

!

Advarsel

Advarsel

!

Advarsel

!

Waarschuwingen

Waarschuwingen

!

Summary of Contents for CentreCOM AT-3012T





























Reviews: